GE PB969DP1BB Installation Instructions Manual

Free-standing electric ranges
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Installation
instructions
Free-Standin
Electric Ran es
Questions?
Call 1-800-GE-CARES
(1-800-432-2737)
or visit www.geappliances.com
In Canada, call 1-800-561-3344
or visit www.geappliances.ca
BEFORE
YOU BEGIN
Read these instructions completely and
carefully.
" IMPORTANT
--
Save
these
instructions for local inspector's
use.
" IMPORTANT
-- Observe a ll
governing codes and ordinances.
,
Note to Installer-
Be sure to leave these
instructions with consumer.
Note to consumer-
Keep these
instructions
for future reference.
,
Skill level - Installation of this appliance
requires a qualified installer or electrician.
,
Proper installation is the responsibility
of the
installer.
o Product failure due to improper installation is
not covered under warranty.
FOR YOUR
SAFETY:
• All ronges can tip.
• BURNS or other SERIOUS
INJURIES con result.
• INSTALL and CHECK the
ANTI-TIP brocket
following
the instructions
supplied
with the brocket.
Anti-Tip Bracket
Kit Included
If you did not receive an anti-tip bracket with your purchase,
call 1-800-626-8774 to receive one at no cost. (In Canada,
call 1-800-561-3344.) For installation instructions of the bracket,
visit: www.geappliances.com.
(In Canada, www.geappliances.ca.)
WARN ING -- Before
beginning the installation, switch
power off at service panel and
lock the service disconnecting
means to prevent power from
being switched on accidentally.
When the service disconnecting
means cannot be locked,
securely fasten a prominent
warning device, such as a tag,
to the service panel.
MATERIALS
YOU MAY NEED
TOOLS
YOU WILL NEED
Drill with 1/8" Bit
Tin Snips
Safety Glasses
Tape Measure
Adjustable Wrench
Pliers
Squeeze Connector
(UL Listed 40 AMP)
Level
1/4" Nut Driver
(For Conduit
4-Wire Cord 4' long OR
Installations
Only)
3-Wire Cord 4' long
r-_
REMOVE
PACKAGING
MATERIALS:
Failure t o
remove packaging
materials could result in damage to the appliance. Remove all packing parts from oven,
racks, heating elements and drawer. Also, remove protective film and labels on the outer
door, cooktop and control panel.
[_
PREPARE
THE OPENING
(FOR INDOOR
USE ONLY)
See illustrations for all rough-in and spacing dimensions.
The range may be placed with 0"
clearance (flush) at the back wall and side walls of the cabinet.
SINGLE OVEN
DOUBLE OVEN
On models with baking
or warming drawers,
electrical outlet must
not be in this area.
,,JJ
30,, iljjJi
/'
/
/
\_.,_
..
"--_.
/
45" /
.
j475/8 '' Acceptable electrical outlet area.
'-_
Orient electrical receptacle so the
.... z
length is parallel to floor.
.............
* GE-branded models have control
panels 30-7/8" wide.
NOTE: Use a 4' power cord to prevent interference
with the storage drawer. Power cords 41/2 to 6' long
may have to be dressed to allow for proper drawer
closing.
MINIMUM DIMENSIONS
BETWEEN
COOKTOP,
WALLS AND ABOVE THE COOKTOP:
A. Make sure the wall covering, countertop, flooring
and cabinets around the range can withstand
the heat (up to 200°F) generated
by the range.
B. Allow 30" minimum clearance between surface
units and bottom of unprotected
wood or metal
cabinet, or allow a 24" minimum when bottom of
wood or metal cabinet is protected by no less
than 114" thick flame retardant millboard covered
with not less than No 28 MSG sheet metal,
(.015"), .015" thick stainless steel, .024"
aluminum or .020" copper.
NOTE C
A_
B
_
C
Both
Sides
i
i
i
i
i
i
i
J
J
i
C. This appliance has been approved for 0" spacing to adjacent surfaces above the cooktop.
However, a 6" minimum spacing to surfaces less than 15" above the cooktop and adjacent
cabinet is recommended
to reduce exposure to steam, grease splatter and heat.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage
space above the cooktop should be avoided. If cabinet storage space is to be provided above the
cooktop, the risk can be reduced by installing a range hood that projects at least 5" beyond the
front of the cabinets. Cabinets installed above the cooktop must be no deeper than 13".
31-10677
]
08-08 JR

Advertisement

Table of Contents
loading

Summary of Contents for GE PB969DP1BB

  • Page 1 ..... • BURNS or other SERIOUS means to prevent power from INJURIES con result. * GE-branded models have control being switched on accidentally. Anti-Tip Bracket • INSTALL and CHECK the panels 30-7/8" wide. When the service disconnecting...
  • Page 2: Single Oven

    ELECTRICAL REQUIREMENTS POWER CORD CONDUIT INSTALLATION It, WARNING: This appliance must be properly grounded. I-A-] Remove wire cover (on the back of range) by removing screws using a 1/4" nut driver. Do not discard these screws. _, WARN IN G: All new constructions, mobile homes, recreational vehicles and installations SINGLE OVEN DOUBLE OVEN...
  • Page 3 3-WIRE INSTALLATION 4-WIRE INSTALLATION Z_WARN IN G: _i,WARN I NG: The neutral or ground wire of the power cord must be connected The neutral wire of the supply circuit must be connected to the neutral terminal to the neutral terminal located in the center of the terminal block and the ground strap located in the lower center of the terminal block.
  • Page 4: Final Installation

    REPLACE THE WIRE COVER LEVEL THE RANGE (CONT.) ,ower Replace wire cover on range back by sliding its left edge under the retaining tabs and replace Position cord so that it does not interfere with drawer. the screws removed earlier. Make sure that no wires are pinched between cover and range back. SINGLE OVEN DOUBLE OVEN Place drawer rail on guides.
  • Page 5: Antes De Comenzar

    Iongitud sea paralela al piso. Pueden provocarse QUEMADURAS u desconexi6n del servicio a fin otras LESIONES GRAVES. * Los modelos de marca GE cuentan con paneles de evitar que el encendido se Kit de soporte de control de un ancho de 30-7/8".
  • Page 6 REQUERIMIENTOS ELC:CTRICOS INSTALACION DE CABLE DE ENERGJA Y DE PASACABLES Z_ADVERTENCIA: Esta unidad debe contar con una adecuada conexi6n a tierra. Quite la tapa del cable (en la parte trasera de la cocina) quitando tornillos mediante una Ilave de tuercas de 1/4". No elirnine esos tornillos.
  • Page 7 INSTALACI(SN DE TRES (3) ALAMBRES E_] INSTALAClON DE 4 ALAMBRES A ADVERTENCIA: AADVERTENCIA: El cable neutral del circuito de suministro debe ester conectado ala El cable neutral o a tierra del cable de energia debe ester conectado a la terminal neutral ubicada en el centro del bloque terminal y la cinta de terminal neutral ubicada en el cen_o inferior del bloque terminal.
  • Page 8: Lista De Control

    REEMPLACE LA TAPA DE LOS CABLES NIVELE LA COCINA (CONT.) Reemplace la tape de los cables de la cocina deslizando el lade izquierdo bajo las leng(Jetas de retenci6n y reemplazando los cinco tornillos quitados antedormente. Verifique que los cables Coloque el cable de modo que no interfiera con el caj6n. no hayan sufrido pellizcos entre la tape y la parte trasera de la cocina.

This manual is also suitable for:

Jb650dp1wwJb650dp1bbJb640dp1wwJb640sp1ssJb640dp1bbJb640mp1bs ... Show all

Table of Contents