Table of Contents
Advertisement
Quick Links
Model: SH-9392AU
Installation and Operating Instructions
FEATURES
• Automatically comes on when motion is de-
tected.
• Automatically turns light off.
• Photocell keeps the light off during daylight
hours.
• Post or pedestal mount.
UNPACKING
Be sure to remove all contents from packaging
and verify all items are present before assembling
this light fixture. This package includes the fol-
lowing items:
• Light Fixture
• Top Cover
• Lens Shields (x2)
• Decorative Pedestal Cover
• Owner's Manual
Before installation, record the model num-
ber listed inside the fixture. Attach receipt
in case of possible warranty issues.
Model Number:
© 2011 The Chamberlain Group, Inc
®
TM
Die-Cast Metal, Motion-
Activated Post Light
REQUIREMENTS
• The light control requires 230 volts AC.
• Recommended mounting height for sensor is 4
to 7 feet above the ground.
• If you want to use Manual Mode, the control
must be wired through a switch.
• It is illegal for persons other than a licensed
electrician or person authorized by legislation
to work on fixed wiring or other electrical
installations.
*Note: Illustrations are for reference only and may
be different from actual product
Lantern*
201104-01A
Advertisement
Table of Contents
Related Manuals for Chamberlain Secure Home SH-9392AU
Summary of Contents for Chamberlain Secure Home SH-9392AU
- Page 1 • Light Fixture • Top Cover • Lens Shields (x2) • Decorative Pedestal Cover • Owner’s Manual Lantern* Before installation, record the model num- *Note: Illustrations are for reference only and may ber listed inside the fixture. Attach receipt be different from actual product in case of possible warranty issues. Model Number: © 2011 The Chamberlain Group, Inc 201104-01A...
- Page 2 IMPORTANT SAFETY AND INSTALLATION INFORMATION Before installing coach light, read all instructions carefully and keep owner’s manual for future refer- ence. • WARNING: To prevent electric shock, please ensure that power is disconnected before installation. • This fixture must be connected to a 230V-240V ~ 50Hz power source. • The fixture must be properly grounded. • This fixture is designed for outdoor installation and should be mounted to a wall. • To achieve best results, this fixture should be mounted 1.2 to 2.1 meters (4 to 7 feet) above the ground. • Do not use dimmer switches or timers with this fixture. The sensor on this light fixture detects “motion” by the movement of heat across the coverage area. However, following are examples of objects that also produce heat and can cause the sensor to trigger: • Pools of Water • Air Conditioners • Dryer Vents • Animals • Heating Vents • Automobile Traffic If you suspect that a heat source of this type is triggering the sensor, reduce the sensitivity. The sensor on this fixture is more sensitive to the movement of heat moving across the coverage area and less sensitive to the movement of heat directly towards it. Motion Motion Sensor Least Sensitive Most Sensitive 201104-01...
-
Page 3: Installation
INSTALLATION PEDESTAL MOUNT This light fixture must be installed by a If mounting on a pedestal, a 76 mm (3") diameter licensed electrician or other person autho- pedestal base or post (not supplied) is required. rized by legislation to work on fixed wiring Before wiring, slide pedestal cover (supplied) onto or other electrical installations. pedestal base or post. See illustrations below. Sensor Assembly WARNING: Turn power off at circuit breaker or fuse. -
Page 4: Testing And Adjustments
WIRING TESTING AND ADJUSTMENTS 1. Turn on the circuit breaker and light switch. WARNING: Turn power off at circuit breaker or fuse. Place tape over circuit minute warm up period Note: Sensor has a 1 breaker switch and verify power is off at before it will detect motion. When first turned the fixture. on wait 1 minutes. -
Page 5: Operation
OPERATION 5. Adjust the SENSITIVITY to increase or decrease the range as needed. Too much sen- Mode: On-Time Works: Day Night sitivity may cause false triggering due to heat Test 5 Seconds sources in the coverage area (see Adjustment 1, 5, or 10 Auto of Coverage Area or Troubleshooting section). Minutes 6. Set the amount of ON-TIME you want the To Dawn* Manual light to stay on after motion is detected (1, 5, or 10 minutes). The timer will reset as long * resets to Auto Mode at dawn. as there is motion present. Once motion has Note: W hen first turned on wait about 1 minutes stopped, the timer will time-out after the for the circuitry to calibrate. -
Page 6: Final Assembly
ADJUSTMENT OF COVERAGE AREA FINAL ASSEMBLY 1. Attach sensor assembly to post using the three The sensor on this light fixture detects “motion” screws supplied. Tighten screws securely. by the movement of heat (body heat) across the 2. Screw top cover onto top of fixture. Hand coverage area. However, following are examples tighten only. of objects that also produce heat and can cause the sensor to false trigger: • Pools of Water • Air Conditioners • Dryer Vents • Fenced-In Animals • Heating Vents • Automobile Traffic Top Cover Decorative If you suspect that a heat source of this type is Screw (2) falsely triggering the sensor and reducing the sensitivity does not solve the problem, then a lens shield (included) can be installed. The plastic lens shield is divided into 3 sections. Each section will... -
Page 7: Specifications
2. Sensitivity is set too high. 2. Reduce sensitivity. Light stays on 1. The sensor may be picking up a heat source like an air 1. Reduce sensitivity. continuously. vent, dryer vent, or brightly painted, heat-reflective surface. 2. Light control is in Manual mode. 2. Switch to Auto. 3. Sensitivity is set too high. 3. Reduce sensitivity. Light flashes on 1. Light control is in the TEST mode and warming up. 1. Flashing is normal under these conditions. and off. 2. Heat being reflected from other objects may be affecting 2. Re-aim sensor. Reduce sensitivity. the sensor. The Chamberlain Group reserves the right to discontinue products and to change specifications at any time without incurring any obligation to incorporate new features in products previously sold. 201104-01... - Page 8 CHAMBERLAIN LIMITED WARRANTY Lighting and Chime Products Chamberlain Australia Pty Limited / Chamberlain New Zealand Limited (Chamberlain) is committed to manufacturing and supplying high quality goods. As part of this commitment, we seek to provide reliable service and support for our goods and are pleased to provide you, the original purchaser, with this Chamberlain Limited Warranty. We also provide the following statement as required by the Australian Consumer Law: In Australia, in addition to your rights under this Chamberlain Limited War- ranty, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Chamberlain’s warranty Chamberlain warrants to the original purchaser of the lighting or chime product (including any LED lights which are provided by Chamberlain as part of the goods) (Unit) that the Unit is free from defects in materials and workmanship for a period of 12 months from the date of purchase. During the applicable Chamberlain Limited Warranty period, if you are concerned that the Unit may be defective, contact your retailer who will provide you with a replacement Unit or refer you to our service centre for a factory repair or replacement. If your retailer refers you to us, call our service centre on the toll free number below and a Chamberlain technician will diagnose the problem. Once the problem has been diagnosed, subject to your rights under the Australian Consumer Law with respect to major failures, Chamberlain will provide you with shipping instructions for a factory repair or replacement.