Freestyle 779 SHARK CLASSIC Instructions

#779 SHARK CLASSIC
WATCH INSTRUCTIONS
FEATURES:
•
CURRENT TIME
•
DAY/MONTH/DATE
•
TWO DAILY ALARM
•
HOURLY CHIME
•
STOPWATCH
•
OPTIONAL 24-HR. TIME
•
WATER RESISTANT TO
300FT/100M
•
™
NIGHT VISION
BACK LIGHT
KEY TO SYMBOLS
LIGHT S1
S3 S2
LIGHT BUTTON:
In order to activate the light feature
on this display, simply press the
light button. The light will remain on
for a few seconds after you release
your finger.
BASIC OPERATION OF
BUTTONS
S1: - Forward selection of data
number
- start/stop chronograph
- toggle alarm on or off
S2: - Split/ reset chronograph
- Select alarm 1 or alarm 2
S3: - Mode change
- Select setting (set or
calibration)
S4: - Back light
- Enter setting mode (press and
hold)
- Exit (setting mode)
MODE CHANGE OPERATION
The mode change sequence is
shown as follows:
TIME DATE ALARM CHRONOGRAPH TIMER
S3 S3 S3 S3
S3
HOW TO USE TIME MODES
- For Time display format, "TM"
label marks are displayed at the
top of left row.
- Hours, minutes and seconds are
displayed at the center row.
- Press and hold S4 for 3 seconds
to enter setting mode, the second
digits start flashing.
- Press S1 (forward) to adjust the
flashing digits. Press and hold S1
for fast scrolling.
- Press S3 to select the next digits
or 12/24H for setting. The setting
sequence is shown as follows:
SECOND HOUR MINUTE YEAR
S3 S3 S3
S3 S3
S3 S3
12/24H DAY MONTH
- When setting seconds, pressing
S1 while the second digits count
between 30 to 59 will reset the
second digits to 00 and 1 will be
added to the minute digits. On the
other hand while second digits
small then 30 will reset the
second digits to 00 and 1 will not
added to the minute digits.
- Year can be set from 2000 to
2049.
- When setting 12/24H, press S1
to toggle 12-hour or 24-hour
display formats. If 24-hour display
format is selected, there will be
no PM symbol will be display.
- After all adjustments are
complete, press S4 to exit setting
mode and weekday will be
adjusted automatically.
Remarks:
1. If there is no button operation for
2-3 minutes in setting mode, the
display will automatically return
back to Time mode or other
mode respectively.
HOW TO USE DATE MODE
- Press S3 to display DATE, "DT"
label marks are displayed at the
left row.
- Month, day and day of week are
displayed at the center row.
HOW TO USE ALARM AND
CHIME
Chime
icon
Alarm
icon
- For Time display format, "AL"
label marks are displayed at the
left row.
- A1/A2 and alarm number are
displayed at the right column.
Alarm time (hours and minutes)
is displayed at the middle. Alarm
status (on or off) is displayed at
the bottom right column.
- Press S2 to select "AL-1" or "AL-
2".
- Press and hold S4 for 3 seconds
to enter setting mode. Alarm
minute digits start flashing. Alarm
is set to "on" automatically when
enter setting mode.
- Press S1 (forward) to adjust the
flashing digits. Press and hold S1
for fast scrolling.
- Press S3 to select next digits.
- When setting chime, press S1 to
toggle the chime function on or
off. If the chime function is "on",
the chime icon will be displayed.
- After all adjustments are
complete, press S4 to exit the
setting mode.
- Press S1 to toggle the alarm
function on or off. If the alarm
function is "on", the alarm icon will
be displayed. The alarm icon is
displayed at the bottom right.
Remarks:
1. There are 2 alarms that work
independently presented by
A1/A2, alarm number, hours,
minutes and status.
2. The alarm sounds for 20
seconds if the alarm function is
"on". Press any button to stop the
alarm sound.
3. If the chime function is "on", the
product will be button
confirmation sound.
4. If 24-hour display format is
selected for time mode, there is
no PM symbol "PM" for alarm
time.
5. If there is no button operation for
2-3 minutes in setting mode, the
display will return back to Alarm
mode automatically.
HOW TO USE CHRONOGRAPH
Reset Run Split
15 sec
- Press S1 to start the chronograph.
- For the first hour, minutes,
seconds and 1/100 second are
displayed. Then hours, minutes
and seconds are
displayed. 1-second resolution after
first hour.
- Press S2 to split time, it will show
"SPL" for 15 second. Then the
display will show current running
times of chronograph.
- Press S1 again to stop the
chronograph. Then press S2 to
go back preset the chronograph.
The chronograph now shows all
zeros and is ready for running
again.
Remarks:
1. The chronograph is of 1/100-
second resolution for first hour
and 1-second resolution for the
reset and with working range up
to 24 hours, then the chronograph
stops automatically.
HOW TO USE TIMER
- Press S1 to start the Timer.
- Press S1 again to stop the Timer.
Then press S2 to go back preset
the Timer. The Timer now shows
the Timer is ready for running
again.
- Press and hold S4 for 3 seconds
to enter setting mode, the second
digits start flashing.
- Press S1 (forward) to adjust the
flashing digits. Press and hold S1
for fast scrolling.
- Press S3 to select the next digits
or Counter Repeat, Counter Stop
for setting. The setting sequence
is shown as follows:
S3 S3 S3
SECOND MINUTE HOUR Counter Repeat
S1
S3
Counter Repeat
- After all adjustments are
complete, press S4 to exit setting
mode.
HOW TO RESET THE DISPLAY
Press and hold S1, S2, S3 buttons
simultaneously, all segments will
be "on", then release the buttons
and the display will be reset. After
reset, test patterns will be shown
for a few seconds and finally the
display will be as follows:
S3