Page 2
Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions 2400.0-2483.5 MHz Country Restriction Reason/remark General authorization required for outdoor use and Bulgaria public service Outdoor use limited to 10 mW...
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N PCI Adapter Model No.: TL-WN851ND Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:...
Make sure that the above items are contained in the package. If any of the above items are damaged or missing, please contact your distributor. Note: The ‘adapter’ mentioned in this User Guide stands for TL-WN851ND 300Mbps Wireless N PCI Adapter without any explanations. 1.2 Introduction The adapter is a 802.11n client device designed to deliver a high-speed and unrivaled wireless...
TL-WN851ND 300Mbps Wireless N PCI Adapter 1.3 Features Complies with IEEE 802.11n, IEEE 802.11g, IEEE 802.11b standards Supports WPA/WPA2 data security, TKIP/AES encryption Supports high rate of up to 300Mbps for maximum throughput, supports automatically adjust to lower speeds due to distance or other operating limitations...
Windows 7 for example. Insert the Resource CD into your CD-ROM drive, and the window below will appear. Select model TL-WN851ND. There will be a menu including: Install Driver&Utility and User Guide. Click Install Driver&Utility to begin.
Page 10
The InstallShield Wizard window will appear. Click Next to continue. Figure 2-2 Choose a setup type. It is recommended to select Install TP-LINK Wireless Configuration Utility and Driver. Selecting Install Driver Only will only install driver. Click Next to continue.
Page 11
TL-WN851ND 300Mbps Wireless N PCI Adapter Click Change to specify the destination location for the software or you can leave it default. Click Next in the screen below to continue. Figure 2-4 Click Install to continue the setup. Figure 2-5...
Page 12
TL-WN851ND 300Mbps Wireless N PCI Adapter The utility and drivers will install. This may take 1~2 minutes. Figure 2-6 After all the steps above, you will see the screen below. Click Finish to complete the setup. Figure 2-7...
Page 13
TL-WN851ND 300Mbps Wireless N PCI Adapter After installation, the utility configuration page will automatically pop up as shown in the following figure and the icon will appear in your system tray. To connect to a network, please refer to Chapter 3 Connect to a Wireless Network.
Method One: To connect using TWCU TL-WN851ND uses the TP-LINK Wireless Configuration Utility as the management software. The utility provides you an easy interface to connect to a network and to change any settings related to the wireless adapter.
Page 15
TL-WN851ND 300Mbps Wireless N PCI Adapter automatically connect to your target network next time if you tick Connect automatically. Figure 3-2 If word None appears behind the SSID, this means the network to be connected is not security-enabled and you can connect to the network without entering a key. To prevent outside intrusion and safeguard your network, it is strongly recommended to set a password to your router or access point.
Page 16
TL-WN851ND 300Mbps Wireless N PCI Adapter Figure 3-4 You have now successfully connected to your network. Click Close to enjoy the Internet. Figure 3-5 To view more information about the network currently connected, click Status in the tools section and the page will display information such as the network type, link quality and...
TL-WN851ND 300Mbps Wireless N PCI Adapter Figure 3-6 3.2 To connect using QSS QSS (Quick Secure Setup) function allows you to add a new wireless device to an existing network quickly. If the wireless router supports QSS or Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless card and router using either Push Button Configuration (PBC) method or PIN method.
Page 18
TL-WN851ND 300Mbps Wireless N PCI Adapter Figure 3-7 The adapter will be connecting to the target network. Figure 3-8...
TL-WN851ND 300Mbps Wireless N PCI Adapter When the following window appears, you have successfully connected to the network. Figure 3-9 3.2.2 PIN method There are two ways to configure the QSS by PIN method: Enter the PIN from your AP device.
Page 20
TL-WN851ND 300Mbps Wireless N PCI Adapter The adapter will be connecting to the target network. Figure 3-11 When Figure 3-9 appears, you have successfully connected to the network. 3.2.2.2. Enter a PIN into your AP device This method is only available in Windows XP and Windows Vista.
Page 21
TL-WN851ND 300Mbps Wireless N PCI Adapter Figure 3-13 When Connect successfully appears on the screen, the QSS configuration is complete. Or you can view the adapter’s utility page to see whether the connection has been successful as shown in Figure 3-15.
TL-WN851ND 300Mbps Wireless N PCI Adapter 3.3 To connect using Windows built-in wireless utility 3.3.1 In Windows 7 Windows 7 users may use the built-in wireless utility. Follow the steps below. Left-click the wireless icon in your system tray (lower-right corner). The utility will display any available wireless networks in your area.
TL-WN851ND 300Mbps Wireless N PCI Adapter Figure 3-17 You have now successfully connected to the network. Figure 3-18 3.3.2 In Windows Vista Windows Vista users may use the built-in wireless utility. Follow the steps below. Open the wireless utility by right-clicking on the wireless computer icon in your system tray...
Page 24
TL-WN851ND 300Mbps Wireless N PCI Adapter Figure 3-19 The utility will display any available wireless networks in your area. Highlight the wireless network you would like to connect and then click Connect. Figure 3-20 If the network you would like to connect is security-enabled, enter the same security key or passphrase that is on your router.
You have now successfully connected to the network. Figure 3-22 3.3.3 In Windows XP Windows XP users may use the built-in wireless utility. Follow the steps below. Right-click on the utility icon in your system tray (lower-right corner). Select Switch to TP-LINK Wireless configuration Utility.
Page 26
TL-WN851ND 300Mbps Wireless N PCI Adapter Figure 3-23 Or double-click the utility icon to load the utility configuration page. Click Advanced in the tools section and then select Use Windows wireless configuration tool in the figure shown below. Click OK when Figure 3-25 appears to continue.
Page 27
TL-WN851ND 300Mbps Wireless N PCI Adapter Figure 3-26 The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) and click the Connect button. Figure 3-27 If the network is security-enabled, you will be prompted to enter the key as shown below. If not, you will connect to the network directly without entering a key.
TL-WN851ND 300Mbps Wireless N PCI Adapter Chapter 4 Management This section will show you how to configure your TL-WN851ND adapter using the TP-LINK Wireless Configuration Utility (TWCU). The TL-WN851ND adapter uses the TP-LINK Wireless Configuration Utility as the management software. The utility provides users with an easy interface to change any settings related to the adapter.
Page 29
TL-WN851ND 300Mbps Wireless N PCI Adapter Figure 4-2 The following items can be found on the screen. Profile Name: Enter a name for your profile (e.g. Home, Office, CoffeeShop). The same name is not allowed. Please also note that no space is allowed between words.
TL-WN851ND 300Mbps Wireless N PCI Adapter Figure 4-3 4.1.2 Modify a profile You may edit an existing profile by clicking the Modify button from the Profile page. For instance, you may like to change the profile name from Home to Home1 or you may want to specify another SSID for profile Home.
The following configurations can be made on the Advanced page: To select wireless configuration tool. Here you can decide which tool to use, either the TP-LINK Configuration Utility or the Windows wireless configuration tool. This option is available only in Windows XP.
TL-WN851ND 300Mbps Wireless N PCI Adapter 4.3 About The About screen gives you information about the Driver and Utility versions of the adapter. Right-click on the icon in your system tray and select About from the list. Figure 4-7...
TL-WN851ND 300Mbps Wireless N PCI Adapter Chapter 5 AP Mode In Soft AP mode, the adapter will work as an AP. This function is available only in Windows7. Suppose that only one computer in your house can access the Internet for various reasons like only one WLAN port is available on your wired broadband router, however, other wireless-capable devices also want to share the Internet.
Page 34
SSID: Enter the name for your soft AP (for example, Jone) so that others can know which AP is yours when trying to connect to it. The default name (SSID) is “tp-link”. Security Type: The security type here is set to be WPA2-PSK which is based on 802.11i and uses Advanced Encryption Standard instead of TKIP.
300Mbps Wireless N PCI Adapter Chapter 6 Uninstall Software 6.1 Uninstall the utility software from your PC On the Windows taskbar, click the Start button, click All programs TP-LINK, and then click Uninstall-TP-LINK Wireless Configuration Utility. Figure 6-1 Uninstall Utility Follow the Install Shield Wizard to uninstall the utility software from your PC.
300Mbps Wireless N PCI Adapter Figure 6-3 6.2 Uninstall the driver software from your PC On the Windows taskbar, click the Start button, click All programs TP-LINK, and then click Uninstall-TL-WN851ND Driver. Figure 6-4 Uninstall Driver Click Uninstall shown in above Figure 6-4, the system will uninstall the driver software of...
TL-WN851ND 300Mbps Wireless N PCI Adapter Appendix A: Specifications Normal Interface 32 bit PCI Interface Standards IEEE 802.11n, IEEE 802.11g, IEEE 802.11b Operating System Windows XP, Windows Vista, Windows 7 Throughput 300Mbps (Maximal) 11b: 1/2/5.5/11Mbps 11g: 6/9/12/18/24/36/48/54Mbps Radio Data Rate...
TL-WN851ND 300Mbps Wireless N PCI Adapter Appendix B: Glossary 802.11b - The 802.11b standard specifies a wireless product networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks.
Page 39
TL-WN851ND 300Mbps Wireless N PCI Adapter Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other...