Honeywell VCC--600N Operation Manual

Operation Manual
OSD Color Camera
VCC - 600N/P
VCC - 600N/P
※ Thank you for choosing Honeywell VCC-600N/P camera.
Please read these instructions carefully before operating this unit,
and retain this manual for future reference.
If you have any problems with this camera, contact your local
supplier to service.
CAUTION for SAFETY OPERATION
1. Water and Moisture
To prevent fire or shock hazard, do not expose this camera
to rain or moisture.
2. Servicing
Do not attempt to disassemble or repair by yourself.
You may be exposed to dangerous voltage or other hazards.
Note that all servicing is qualified service personnel.
Modifications not approved by manufacturer could
void the user's authority to operate the equipment.
3. Power Sources
To prevent electric shocks and risk of hazards, do NOT use
more than the specified power source.
4. Environment
Do not install too warm or too cold place. Recommended
operation temperature is between -5℃ and 50℃
5. Sunlight
Do not point the camera at the sun. CCD can be damaged.
6. Heavy Shock and Vibration
Do not drop the camera or subject it to heavy shock of
vibration.
7. Install on an Unstable Place
Do not place or install this camera on an unstable place,
stand, tripod, bracket or table. That may cause serious injury
to people or damage to appliance.
TROUBLESHOOTING
Before sending the camera out for repair, check the items
below. If the problem persists after checking these items,
contact your service center.
In case of no image
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been adjusted correctly?
In case of unclear image
Is the lens in focus?
Is the lens dirty?
Is the monitor adjusted correctly?
※ Dirt of fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
DIMENSIONS
Unit: mm
ENTER ENTER
CO NT CO NT
PO WER PO WER
DC12V DC12V
DC DC VSD VSD
+ + - -
MD MD
8. When operation is incorrect or a malfunction is observed
While operating, if any abnormal condition (strange sound,
smell or smoke) or a malfunction (no pictures, etc.) is
observed, stop using the camera immediately, turn the
power off, then contact your supplier.
9. Cleaning
Turn the power off and wipe off the dirt with a dry soft
cloth. If it is extremely dirty, use furniture cleaner to wipe it
off. To clean the lens, use a blower or lens cleaning
tissue. (available from any camera dealer)
10. Do not shoot any source of bright light.
If the objects contain very bright areas, bright vertical or
horizontal lines may appear on the screen. This is called
"smear" , a Phenomenon which often occurs with solid
- state pickups, and is not a malfunction.
11. Damage Requiring service
Unplug the camera from the power source and refer
servicing to qualified service personnel under the following
condition:
A. If the power-supply cord or plug is damaged.
B. If the camera has been exposed to rain or water.
C. If liquid has been spilled, or objects have fallen into the camera.
D. If the camera does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the camera to its normal operation.
E. If the camera has been dropped or the cabinet has been damaged.
F . If the camera exhibits a distinct change in performance.
G. Warranty is not covered in case of natural disaster or wrong
Installation.
NAMES & FUNCTIONS
UP BUTTON
ENTER BUTTON
(-) BUTTON
LENS
ENTER
VIDEO
CONT
POWER
DC12V
DC VSD
+ -
MD
POWER ON LED
This LED is ON
in power ON state.
LENS LENS
Power Input Terminal and MD Alarm Output
VIDEO VIDEO
INSTRALLATION
Mounting a lens
1. Remove the Protective cap in front of the camera.
2. Confirm the mount ring whether it is for C or CS.
3. Attach the lens to the lens mount ring.
4. If the lens has an Auto Iris mechanism, connect the iris cable to the
LENS in rear of the camera.
① In the case of having no iris amplifier : Set the slide switch to
DC (Down side).
② In the case of having iris amplifier : Set the slide switch VSD
(Upper side)
※ When connecting Auto iris lens, be sure to use the connector to
be recommended by manufacturer.( E4-191, ChuoMusen, Japan)
VSD LENS PIN CONFIGURATION
3 4
1 2
1. Power(12V)
3. Video Signal
Back focus adjustment
1. In case of fixed focus lens
① Loosen the locking ring with L type wrench and set the focus ring
of lens to infinity ( ∞ ).
② Tune the mount ring to get a clear picture( distance from camera
to object is more than 23m) and fasten the locking ring.
2. In case of zoom lens
① Loosen the locking ring with L type wrench and set the lens to the
maximum telephoto position. Then turn the focus ring to focus.
※ In the case of Auto iris lens only, shoot a comparatively dark
object or reduce the ambient light so that the aperture is fully open.
② Set the lens to its maximum wide angle position, and set the focus.
③ Repeat step ① and ②, until the difference between focusing
position ① and ② is smallest.
④ When the best focusing point in found, fasten the locking ring.
Connection of power supply
Must be checked the power source from the external power supply
before power on.
OSD MENU
GENERAL SETUP
SYNC
DOWN BUTTON
BURST
CONTRAST
(01...100)
RETURN
(+) BUTTON
CAMERA SETUP
AE MODE
LENS CONNECTOR
WB MODE
BLC MODE
their level, area setting.
PZM SET
NIGHTSHOT
CAMERA ID
RETURN
MEM FUNC. SETUP
DNR MODE
setting. (OFFLOWHIGH)
PIP MODE
QUAD MODE
MD MODE
D.ZOOM
VIDEO OUTPUT MIRROR
RETURN
Composite Video
Signal Output
SPECIAL SETUP
SHARPNESS
GAMMA
LANGUAGE
RETURN
Lens Type Select Switch
DC Lens: with no iris amp.
DEFAULT SETUP
VSD Lens: with iris amp.
FACTORY DEFAULT
RETURN
EXIT SETUP
SAVE AND EXIT
EXIT
RETURN
DC IRIS LENS PIN CONFIGURATION
3 4
①③ ①③
② ④ ② ④
1 2
2. No Connection 1. Control - 2. Control +
4. GND 3. Drive + 4. Drive -
SYNC LEVEL adjustment (01...255)
BURST LEVEL adjustment (01...255)
CONTRAST LEVEL adjustment
Return to the previous menu.
LENS MODE, SHUTTER, AGC, BRIGHTNESS, MAX AGC,
MAX FIELDS, etc.
AWC LOCK, AWC AUTO, ATW, INDOOR, OUTDOOR,
MANUAL, etc.
OFF, BLC, WDR, BMB and
Privacy Zone Masking function setting.
Day  Night, Night  Day mode setting.
Camera ID and Position setting.
Return to the previous menu.
Digital Noise Reduction mode
Picture-in-picture mode setting.
Quad display mode setting.
Motion Detection mode setting.
Digital Zoom setting. (OFF1.0x...16.0x)
Mirror mode setting. (OFFH.MIRRORV.MIRRORFLIP)
Return to the previous menu.
Sharpness compensation setting. (0~15)
Gamma compensation setting. (0.36~1/USER , 8steps)
OSD Language setting. (ENG, KOR, JPN, CHI1, CHI2)
Return to the previous menu.
Set to the Factory Default.
Return to the previous menu.
Return to the previous menu.
The contents of the package
Check the below contents
- VCC-600N/P Camera 1set
- Auto Iris Lens Plug
- L Type Wrench
- Operation Manual (English)
SPECIFICATIONS
MODEL NAME VCC-600N VCC-600P
Operational
Video Standard NTSC PAL
Image Sensor SONY 1/3" Super HAD CCD
Total Pixel 410,000 Pixels 470,000 Pixels
Effective Pixel 380,000 Pixels 440,000 Pixels
Scanning System 525 Lines, 2:1 Interlace 625 Lines, 2:1 Interlace
Scanning Frequency 15.734kHz(H), 59.94Hz(V) 15.625kHz(H), 50Hz(V)
Sync System INTERNAL
S/N Ratio More than 50dB
0.1lx (F=1.2, 50IRE)
Min. illumination
0.001lx (F=1.2, 50IRE, MAX FIELDS x512)
Horizontal Resolution 540 TV Lines
Video Output VBS 1.0Vp-p / BNC
Lens Iris Control MANUAL / DC / VSD
Electronic Shutter 1/60 ~ 1/100,000 sec 1/50 ~ 1/100,000 sec
AGC OFF - 36dB
Back Light Compensation OFF / BLC / WDR / BMB
White Balance AWC LOCK / AWC AUTO / ATW / INDOOR / OUTDOOR / MANUAL
Electrical
Rated Voltage DC12V ± 2V
Power Consumption 1.5W (max)
Mechanical & Environmental
Lens Mount CS Mount
Weight 181g
Dimensions 61.6[W] x 52.4[H] x 77.8[D]mm
Front & Rear Color Pantone Color 11C (Gray)
Body Color Gray
Operating Temp. -10°C ~ +50°C
Storage Temp. -20°C ~ +70°C
Operating Humidity 90% RH (non-condensing)
Honeywell Security Group
Honeywell Co., Ltd.
Address: 5F, Sangam IT Tower, B4 - 4block, 1590
Sangam-dong, Mapo-gu, Seoul 121-835, Republic of
Korea
Printed in Korea
TEL: +82 2 799 6020 / 6395 / 6006
D-100073-001, REV.0
FAX: +82 2 792 9011
E-mail: info.security@honeywell.com