Advertisement
3.
FENCE/FOUNDATION TRIMMING. Approach trim-
ming around chain link fences, picket fences, rock
walls and foundations slowly to cut close without whip-
ping line against the barrier. If the line comes in contact
with rock, brick walls, or foundations, it will break or
fray. If line snags fencing, it will snap off.
4.
TRIMMING AROUND TREES. Trim around tree
trunks with a slow approach so line does not contact
bark. Walk around the tree trimming from left to right.
Approach grass or weeds with the tip of the line and tilt
linehead slightly forward.
5.
SCALPING Scalping refers to removal of all vegeta-
tion down to the ground. To do this, tilt the linehead to
about a 30 degree angle to the left. By adjusting the
handle you will have better control during this opera-
tion. Always keep a distance of 100 feet (30 meters)
from other people and animals when scalping. Do not
attempt this procedure if there is any chance flying
debris could injure operator, other people or cause
damage to property.
6.
SWEEPING - DO NOT SWEEP WITH TRIMMER
(Fig. 4C)
Fig. 4C
MAINTENANCE
•
REPLACING TRIMMING LINE- STANDARD
HEAD
1.
Turn knob (A) COUNTERCLOCKWISE and remove
(Fig. 5A). User knob spanner supplied.
2.
Remove spool (B) and spring (C) from spindle (D).
3.
Remove any remaining trimming line (H).
4.
Double a 14' (4.3m) length of .080" (2mm) trimming
line. Place the looped center in one of the slots of the
spool divider (Fig. 5B).
5.
Wind trimming line clockwise as shown in illustration
(Fig. 5C), keeping tension, with each half separated
by the spool divider. Wind to within 6" (15cm) of the
ends.
6.
Lock each end of line (H) into a slot (F) on opposite
sides of the spool (Fig. 5D).
7.
Install the spring (C) over the spindle (D). Insert each
end of the line through an eyelet (G) in the housing
(E) (Fig. 5E).
8.
Lower the spool into the housing (E) while feeding the
line through the eyelets (G). Ensure the spring seats
itself into the spool (Fig. 5E).
9.
Once the spool is in place, apply pressure on the
spool compressing the spring. Pull each end of the
line (H) sharply to unlock the line from the slots (Fig.
5F).
10. Continue to apply pressure to the spool until the knob
can be threaded CLOCKWISE onto the spindle.
Tighten the knob securely by hand only (Fig. 5G).
11. Trim the excess line to approximately 5" (13cm).
Fig. 5A
H
D
A
F
C
H
A. KNOB
B. SPOOL
C. SPRING
B
D. SPINDLE
E. HOUSING
F. SLOTS
G. EYELETS
H. TRIMMING LINE
Fig. 5B
Fig. 5C
G
F
F
C
H
E
Fig. 5D
Fig. 5E
H
H
Fig. 5F
Fig. 5G
6
AU
•
CLEANING
1.
Regular cleaning and maintenance of your line trim-
mer will ensure efficiency and prolong the life of your
machine.
2.
After each cutting operation, take apart and clean out
the grass and soil from: the spool and its slot, the
whole trimmer and in particular the guard.
3.
During operation, keep the air slots clean and free of
grass.
4.
Only use a cloth soaked with hot water and a soft
brush to clean the line trimmer.
5.
Do not spray or wet the appliance with water.
6.
Do not use detergents or solvents as these could ruin
the trimmer. The parts in plastic can easily be dam-
aged by chemical agents.
G
•
SERVICING DOUBLE-INSULATED APPLI-
ANCE
In this double-insulated appliance, two systems of insula-
tion are provided instead of grounding. No grounding
means is provided on a double-insulated appliance, nor
should a means for grounding be added to the appliance.
There are no owner serviceable parts inside. A double-
insulated appliance is marked with the words, "DOUBLE
E
INSULATION" or "DOUBLE INSULATED". The symbol
(square within a square) may also be marked on the appli-
ance.
Any service must only be carried out by a qualified tech-
nician at an authorized service centre.
1.
Place switch in "OFF" position and unplug the power
supply before the appliance is serviced, cleaned or
maintenance is performed.
2.
Keep air intake clean and air vents free of debris to
avoid overheating the motor.
3.
Clean with a damp sponge and mild soap. Do not
squirt with water, hose with water or other liquids.
4.
No lubrication is necessary as the motor is equipped
with lifetime lubricated bearings.
5.
If the unit does not operate, turn switch to "OFF" posi-
tion and disconnect extension from power supply first,
D
then from unit. Check power supply for blown fuses or
tripped circuit breakers. Do not attempt to repair it
yourself. There are no serviceable parts inside.
G
7
AU
Advertisement
