Advertisement
Quick Links
Georgian Bay 36/41"
Installation Instructions
Models:
36DVBGTKCB, 36DVBGTKB
41DVBGTKCB, 41DVBGTKB
DVBGTKCB – Classic Black Cast Iron
DVBGTKB – Ebony Black Enameled Cast Iron
The Georgian Bay is designed for use on fireplace mod-
els 36XDV (36"), DV360 (41") and DVRT41 (41").
NOTE: Cast iron parts can be heavy, an assistant
would be advisable for this installation.
CAUTION: Porcelain enamel is fragile. The finish can
be easily damaged if castings are not handled carefully.
Always place castings on a protective surface, such as
a towel, blanket or carpet.
Check Contents of Shipping Carton
Compare contents of carton in Figure 1 with actual
parts received. If any parts are missing, or damaged,
contact your local dealer before starting installation.
Contents: (Fig. 1) Top Dome Section, Main Body Sec-
tion, knob extensions (2), Top Heat Deflector, Screws (4)
Top Heat
Deflector
Main Body
Section
Screws
Knob Extensions
CAR191
Fig. 1 Carton contents.
Top Dome
Section
������
�������� ��� ��������
Tools required: Phillips screwdriver, measuring tape
NOTE: It is our recommendation that you
install the Georgian Trim, if purchased, be-
fore you install the Georgian Bay. This will
help reduce damage to both cast units.
Fireplace Unit Preparation
Before you start your bay installation the fireplace unit
needs to have some items removed. (Fig. 2)
1. Remove the top louvre by gently sliding the louvre
upward and away from the unit.
2. Remove the sheet metal top flange located on the
bottom side of the top louvre opening. You will need
to remove between 2-5 Phillips screws that are hold-
ing the flange in place.
3. Remove the bottom louvre by removing 4 Phillips
screws or by pulling the hair pins that are holding the
hinge pins in place on the unit.
Fig. 2 Remove the fireplace top and bottom louvre and top
flange.
�����
4. Install the top heat deflector shield by aligning the
������ ������
holes of the shield with the four (4) inside holes on
�����
the fireplace top flange. Use the four (4) screws sup-
plied to attach the shield to the unit. (Fig. 3)
This completes the fireplace unit preparation.
Top Flange
Top
Louvre
Bottom
Louvre
KT696
30003743 5/08 Rev. 1
Advertisement
Related Manuals for Vermont Castings TrimWorks 36DVBGTKCB
Summary of Contents for Vermont Castings TrimWorks 36DVBGTKCB
-
Page 1: Installation Instructions
Tools required: Phillips screwdriver, measuring tape NOTE: It is our recommendation that you install the Georgian Trim, if purchased, be- fore you install the Georgian Bay. This will help reduce damage to both cast units. Fireplace Unit Preparation Before you start your bay installation the fireplace unit needs to have some items removed. - Page 2 Main Body Section Measure Here Finished Top Heat Deflector Floor Shield KT698 ����� Fig. 5 Measure from underside of bay to finished floor. ������� ���� ����� 4. Loosen the 8 screws on the bottom flange, but do KT744 ����� not remove, and lower the bottom flange down by Fig.
- Page 3 6. Place the top dome section onto the main body sec- Top Dome Section tion by lifting the top dome section over the top edge Slotted Slotted Groove Groove of the main body section. You will notice on the back side of the top dome section two slotted grooves in the sheet metal.
- Page 4 Georgian Bay 36”/41” (continued) 36DVBGTKCB 41DVBGTKCB 36DVBGTKB 41DVBGTKB Ref. Description Classic Black Classic Black Ebony Ebony 1. Eyebrow, Left 30003718 30003764 30003780 30003792 2. Eyebrow, Right 30003719 30003765 30003781 30003793 3. Frame, Left Dome 30003720 30003766 30003782 30003794 4. Frame, Right Dome 30003721 30003767 30003783...