NEC LT150Z Quick Connect Manual

LT150Z Quick Connect Guide
Connections
Step 1 Connect the supplied 15pin-15pin signal cable.
Mini D-Sub 15 pin
connector
RGB signal cable
(supplied)
Audio cable
(not supplied)
For older Macintosh computers, use a commercially
available pin adapter to connect to your Macintosh's
video port.
Step 2 Connect the supplied power cable.
IN
AC
RD
CA
PC
B
O US
VI DE
DE O
S- VI
B L
RG RO
NT
CO
PC
DI O
AU
Step 3 Turn on the Projector.
OFF ON
POWER
VIDEO S-VIDEO RGB1 RGB2
AUTO ADJ. LASER
A U
D IO
R G
SELECT
B
S -V
ID E
O
NOTE: To turn off the projector, press and hold the Power "ON/STAND BY" button for a minimum of two seconds.
Step 4 Set up the Projector.
To adjust the projector's focus and zoom use the Focus ring and the Zoom ring on the lens.
AUD IO
RGB
S-VI
DEO
PC CON
TRO L
VIDE O
USB
PC CAR
D
AC
IN
A U
D I O
R G
B I
N P
U T
A U
D IO Adjusting the Tilt Foot.
R G
B
S -V
ID E
O
P C
C O
N T
R O
L V ID
E O
1
Power down all equipment
before making connections.
Power cable
(supplied)
1. Lift the front edge of the projector.
2. Press the Tilt button on the top of the projector to extend the Adjustable Tilt Foot.
3. Press and hold the Tilt button.
4. Lower the front edge of the projector to the desired height and release the Tilt button to lock the
Adjustable Tilt Foot.
• If the projected image does not appear square to the screen then use keystone correction for proper adjustment. See
page 28 or 34 of the supplied user's manual.
Zoom ring
Focus ring
4
2 3
1 4
To fine-adjust the height of the rear foot,
remove the spacer and rotate the rear foot
Spacer to the appropriate height.
Remote Control Features
1 2 3
10. RGB 2 Button
Not available on this model.
4
11. AUTO ADJ Button
6
5 Use this button to adjust an RGB source for an
OFF ON
optimal picture. Some signals may not be dis-
POWER
8 9 played correctly or take time to switch between
VIDEO S-VIDEO RGB1 RGB2 sources.
7 10
AUTO ADJ. LASER 12. LASER Button
11
12
Press and hold this button to activate the laser
pointer. When lit, you can use the laser to draw
13
your audience's attention to a red dot that you
can place on any object.
14
SELECT
13. MENU Button
15 Displays the menu for various settings and ad-
16
justments.
17
PJ 14. SELECT (▲▼
19
When you are in the Computer mode, these
buttons work as a computer mouse.
22
When you are in the Projector mode, which is
FOCUS ZOOM SHIFT
18 20 indicated by lighting the PJ button:
▲▼:
HELP POINTER PC CARD Use these buttons to select the menu of
21 28
the item you wish to adjust.
KEYSTONE MAGNIFY SLIDE
: Use these buttons to change the level of a
23
29 selected menu item.
A press of the
24
FREEZE VOLUME FOLDER
lection.
25 30
When the pointer is displayed, these ▲▼
PIC-MUTE SLIDE
26
buttons move the pointer.
31
LIST
27
15. ENTER (Left Click) Button
When you are in the Computer mode, this but-
ton works as the mouse left button.
1. Infrared Transmitter When this button is pressed and held for a mini-
mum of 1.5 seconds, the drag mode is set.
Direct the remote control toward the remote
When you are in the Projector mode, which is
sensor on the projector cabinet.
indicated by lighting the PJ button:
Use this button to enter your menu selection. It
2. Laser Pointer
Beams a laser light when "Laser" button is works the same way as the "Enter" button on
the cabinet.
pressed.
3. Remote Jack 16. CANCEL (Right Click) Button
When you are in the Computer mode, this but-
Not available on this model.
ton works as the mouse right button.
When you are in the Projector mode, which is
4. LED
indicated by lighting the PJ button:
Flashes when any button is pressed.
Press this button to exit "Menus". It works the
same way as the "Cancel" button on the cabi-
5. Power ON Button
If the main power is applied, you can use this net.
button to turn your projector on.
17. PJ Button
6. Power OFF Button Press this button to switch the Select, Cancel,
and Enter buttons between the Projector mode
If the main power is applied, you can use this
button to turn your projector off. (lit red) and the Computer mode. Press this
button or any one of the Power ON/OFF, Menu,
NOTE: To turn off the projector, press and hold the
Help, Pointer, Magnify, PC Card, Folder List or
POWER OFF button for a minimum of two seconds.
Slide List buttons to switch to the Projector
mode and the PJ button lights red. To switch
7. VIDEO Button
back to the Computer mode, press the PJ but-
Press this button to select an NTSC, PAL,
ton again.
SECAM or NTSC4.43 compatible video source
from a VCR, DVD player, laser disc player or
18. FOCUS Button
document camera.
Not available on this model.
8. S-VIDEO Button
19. ZOOM Button
Press this button to select an S-Video source
Not available on this model.
from a VCR.
20. SHIFT Button
9. RGB 1 Button
Not available on this model.
Press this button to select a video source from
computer or component equipment connected
Printed in Japan
to your RGB port.
7N8P0771
21. HELP Button
Provides information about operation and ad-
justment procedures or the set information for
the current menu or adjustment during menu
operation.
22. POINTER Button
Press this button to display one of the eight
pointers; press again to hide the pointer. You
can move your pointer icon to the area you want
on the screen using the Select button.
23. KEYSTONE (+) (–) Button
Press the (+) or (–) button to correct the key-
stone (trapezoidal) distortion, and make the im-
age square.
24. MAGNIFY (+) (–) Button
Use this button to adjust the image size up to
400%.
When the pointer is displayed, the image is
magnified about the center of the pointer. When
the pointer is not displayed, the image is mag-
) (Mouse) Button
nified about the center of the screen.
When the image is magnified, the pointer is
changed to the magnifying icon.
25. FREEZE Button
This button will freeze a picture. Press again to
resume motion.
26. PICTURE MUTE Button
button executes the se-
This button turns off the image and sound for a
short period of time. Press again to restore the
image and sound.
NOTE: When the menu is displayed, a press of
this button mutes an image and sound without
turning off the menu.
27. VOLUME (+) (–) Button
Press (+) to increase the volume and (–) to de-
crease it.
28. PC CARD Button
Press this button to select the PC Card Viewer
source.
29. SLIDE (+) (–) Button
Press (+) to select the next folder or slide and
(–) to select the previous folder or slide.
30. FOLDER LIST Button
Press this button to select PC Card Viewer
source to display a list of folders included in a
CompactFlash card.
31. SLIDE LIST Button
Press this button to select PC Card Viewer
source to display a list of slides included in a
CompactFlash card.
*NOTE: The default is the Computer mode, which
allows you to use the Select, Cancel, and Enter but-
tons as your computer mouse. When the POWER
ON/OFF, MENU, HELP, POINTER, MAGNIFY, PC
CARD, FOLDER LIST, or SLIDE LIST button is
pressed, the PJ button lights red to indicate that you
are in the Projector mode. If no buttons are pressed
within 10 seconds, the light goes out and the Projec-
tor mode is canceled.