Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
GL1800 HIGH PERFORMANCE DRIVING/LED FOG LIGHTS
2001-2005 PART NO. FG105 (NON-AIRBAG)
2006-2010 PART NO. FG610 (WITH AIRBAG)
Congratulations on your purchase!
This product is intended for aftermarket use and have been fit checked on stock, non-modified OEM motorcycles. As with any aftermarket products,
there may be some slight modifications required. If you are not comfortable with any installation steps, please consult a qualified motorcycle
technician to perform the work. Always allow lights to cool down before touching them.
Non U.S. Motorcycles: This kit may not be Plug 'N Play on non U. S. spec motorcycles.
PARTS LIST
LED FOG LIGHT
RIGHT MOUNTING BRACKET (AFFIXED)
LEFT MOUNTING BRACKET (AFFIXED)
4MM SPACER
16MM SPACER
20MM SPACER
35MM SCREW
50MM SCREW
M6 WASHER (flat)
ZIP TIE
ON/OFF SWITCH
JUMPER
*RELAY HARNESS
(DEPENDING ON YOUR MODEL, 1 MAY BE INCLUDED)
**PLEASE READ THIS REFERENCE SHEET THOROUGHLY BEFORE STARTING INSTALLATION**
IMPORTANT
MOTORCYCLE SETTINGS: The memory settings of the suspension system, trip meter, clock, and radio will be lost when disconnecting the negative
battery cable. Reset your settings after reconnecting the battery. Upon completion of the installation, be sure to check that all components are
working properly by doing a thorough inspection before riding.
WARRANTY: We will replace a unit under warranty due to LED failure. Warranty does not cover condensation as this could be a result of riding in
different weather conditions. Please see product page at SoCalMotoGear.com for additional details. International customers outside of the U.S., please
contact your local dealer.
INSTALLATION PREPARATION:
A. Place motorcycle on center stand.
B. Disconnect the negative cable from the battery.
C. Remove the lower front cowl following your service manual instructions.
Secure all wiring away from any moving parts or extreme heat with zip ties.
D. [Skip this step if you currently have fog lights installed.] Remove your existing lights.
Using cutters, remove the plastic knockouts from the lower front cowl and smooth edges with a Dremel® or file.
NOTE: Right side of bike is the throttle side; left side is the clutch side.
© Copyright 2024 SoCalMotoGear. All Rights reserved. Ver. 1.1
FOR SERVICE / SUPPORT CONTACT: Service@SoCalMotoGear.com
QTY
2
1
1
1
2
1
3
3
6
3
1
1
Please obey all state and local laws regarding the use of additional lighting.
"Riding at Night has Never Been Brighter"
–
EACH MODEL IS AVAILABLE IN :
BLACK
CHROME
PRE - INSTALLATION REMINDERS:
A. IMPORTANT – Place motorcycle on center stand and always perform work in
a well-ventilated area.
B. Watch our Installation Video: www.SoCalMotoGear.com/FGvideo
C. To download/view the complete manual, please visit:
www.SoCalMotoGear.com/FGmanual
...continued
Page 1 of 3
Advertisement
Summary of Contents for PATHFINDER L.E.D. FG105
- Page 1 INSTALLATION INSTRUCTIONS GL1800 HIGH PERFORMANCE DRIVING/LED FOG LIGHTS “Riding at Night has Never Been Brighter” 2001-2005 PART NO. FG105 (NON-AIRBAG) 2006-2010 PART NO. FG610 (WITH AIRBAG) – FOR SERVICE / SUPPORT CONTACT: Service@SoCalMotoGear.com Congratulations on your purchase! This product is intended for aftermarket use and have been fit checked on stock, non-modified OEM motorcycles. As with any aftermarket products, there may be some slight modifications required.
- Page 2 Installation Instructions For PathFinderLED GL1800 High Performance Driving/LED Fog Lights ® NOTE: Read instructions thoroughly before installing. STEP 1. Locate Right and Left FOG LIGHT with the affixed mounting brackets. [Markings can be found on the light/mounting brackets: “L” left and “R” right.] STEP 2.
- Page 3 Figure 9 STEP 5. [Figure 9] Remove Allen screw and remove left control panel. STEP 6. [Figure 9] Remove switch cover on back of control panel. STEP 7. Remove two screws holding switch cover to control panel. STEP 8. Install the switch using the screws removed in the previous step. STEP 9.