panas EX-10 Series Instruction Manual

INSTRUCTION
MANUAL
EX-10 Series
Thank you very much for purchasing Panasonic products.
Read this Instruction Manual carefully and thoroughly for
the correct and optimum use of this product. Kindly keep
this manual in a convenient place for quick reference.
Refer to the "EX-10 Series User's Manual" (our
Website:
If you could not visit our web site, contact our sales
1 SAFETY PRECAUTIONS
Always observe
WARNING
Do not use this product for an application where it directly
detects the human body. Otherwise, there is a risk of death
or serious injury.
Do not use the / for an application either
where it directly detects the human body or where it
indirectly protects the human body. Otherwise, there is a
risk of death or serious injury.
When the human body needs to be detected for safety
application, use products that conform to the laws and
standards related to human body detection for safety ap
plication in each country, such as OSHA, ANSI, and IEC.
2 CAUTIONS
This product has been developed / produced for industrial use
only.
EX-14
tive object (e.g., a conveyor, etc.) in the background of the
2
The thin cable 0.1mm is used for this product. Thus, take
care that if the cable is pulled with excessive force, it may
cause cable break.
2
beam type), or less, is possible with 0.3mm , or more of con
ductor area cable.
Make sure to carry out wiring in the power supply OFF condi
tion.
Take care that wrong wiring will damage the sensor.
Verify that the supply voltage variation is within the rating.
If power is supplied from a commercial switching regulator,
ensure that the frame ground (F.G.) terminal of the power
supply is connected to an actual ground.
In case noise generating equipment (switching regulator,
inverter motor, etc.) is used in the vicinity of this product, con
nect the frame ground (F.G.) terminal of the equipment to an
actual ground.
lines or put them in the same raceway. This can cause mal
function due to induction.
device or sunlight etc., as it may affect the sensing perfor
mance.
Do not use during the initial transient time (EX-15
others: 50ms) after the power sup
ply is switched ON.
This sensor is suitable for indoor use only.
Do not use this sensor in places having excessive vapor, dust,
etc., or where it may come in contact with corrosive gas, etc.
Take care that the sensor does not come in contact with oil,
grease, organic solvents such as thinner, etc., strong acid, or
alkaline.
This sensor cannot be used in an environment containing
Never disassemble or modify the sensor.
Since the cable end is not waterproof, do not use the sensor
in the application where water may seep in from the cable
end.
3
REGULATIONS AND STANDARDS
This product conform to the following regulations and
standards.(The / is excluded from this.)
4 PART DESCRIPTION
mode switch on bifurcation
Stability indicator
(Green) (Note)
L i g h t s u p u n d e r t h e
stable light condition or
the stable dark condition
Operation indicator
(Orange) (Note)
L i g h t s u p w h e n t h e
sensing output is ON
5 MOUNTING
Flat washer
Nuts
Sensing
11
direction
Spring
washer
Attached screw
Thickness of
[M2 (length 10)]
mounting plate:
Thickness of
2.5 or less
mounting plate: 2 or less
6 WIRING DIAGRAMS
Load
(Note 2)
Notes: 1)
the output (black).
EX-15E
Panasonic Industry Co., Ltd.
Panasonic Industry Co., Ltd. 2024
EX-10
Web
downloads/?tab=manual
Web
1
Operation mode
switch
Operation indicator
(Orange)
Lights up when the
sensing output is ON
IEC
2
Sensing
EX-14
direction
11
0.1mm
Attached screw
[M2 (length 8)]
50m
(Note 1)
(Note 2)
Load
100ms
PRINTED IN JAPAN
3
EU
ISO 13849-1:2015(
https://industry.panasonic.com/jp/ja/
4
EX-10
1
5
OSHA ANSI
/
( )
2
6
2
0.3mm
F.G.
1
2
F.G.
EX-
50ms
Panasonic Industry Co., Ltd. 2024
/
EMC 2014/30/EU
EMC 2016/1091
EN IEC 60947-5-2:2020
1 PLc)
1
L ON
D ON
1
ON
ON
0.2N·
ON ON
11
11
M2 10
M2 8
2 2.5
NPN PNP 1
V V
2
2
0V 0V
mm