Oliveri Naples NA369C-1P Installation Instructions

THIS TOILET MUST BE INSTALLED BY A LICENSED PLUMBER IN
ACCORDANCE WITH LOCAL REGULATIONS
Remove all products from packaging:
Check the product for damage, if the product is damaged return to store of purchase.
Check the product is complete with all components required to install.
This product is to only be installed by a licensed plumber, failing to do so will void warranty.
This product is to be installed as per Australian Standard and local authority requirements.
WARNING: DO NOT BED THE PAN IN PLACE USING CEMENT, CONCRETE OR SIMILAR
MATERIAL, DOING SO WILL VOID THE PRODUCT WARRANTY.
2.Place the pan into position centralising the pan on your centre line, draw around the pan
base and mark the entry points on the floor to where the floor fixing holes are on the side of
the pan.
3.Remove the pan and drill and screw into place the floor fixing brackets, set the floor fixing
brackets 15mm inside the line drawn around the base of the pan. Use suitable floor fixing
screws and toggles to suit the floor material.
4. Critical: The pan must be on a level surface square to the wall, if the floor slopes away the
pan will need to be levelled using suitable floor chocks around the pan to support and stabi-
lise the pan.
5.The standard variance bend( 166241) supplied has a set out of 50mm to 160mm, the option-
extra.
" S" trap installation
6.Place the variance bend into the floor outlet, from the finished floor to the centre of the pan
outlet is 180mm, ensure the variance bend is straight and square to the wall and centralised
to the pan outlet height, assemble the variance bend wall brace and fix to the finished wall.
Measure the distance from the back edge of the pan to the "P" trap edge and add on suffi-
cient length for the Variance bend collar to fully engage the "P"trap.
Remove the locking ring and rubber boot from the Variance bend. The distance between each
ridge on the Variance bend is 10mm. Once the excess has been cut off the variance bend
reassemble the rubber boot and locking ring.
2019-08/Version 2.0
Product code: NA369C-1P
NA369C-2C
NA5011
7.If the Suite is being installed as a bottom entry inlet refer to bottom entry cistern installation
before sliding the pan into place.
8.Slide the pan into place being careful that full engagement of the pan variance bend has
been achieved.
N.B
pre-soaping the rubber boot on the Variance bend will assist with easier engagement of
variance bend.
9.Once the pan is in place and connected to the Variance bend screw the pan in place using
the supplied fixing screws and cover.
DO NOT OVER TIGHTEN SCREWS AS THIS MAY CAUSE THE PAN TO CRACK.
Cistern Installation:
Bottom Entry only (Preassembly requirement before connecting pan to variance bend):
1.Locate the cistern on to the pan with the sponge gasket placed on the cistern outlet valve
tail and connect the tank to pan using attachment bolts.
(N.B Cistern to Pan assembly bolts are to be tightened down evenly, alternating between the
left and right bolt until the cistern and pan have china to china contact).
DO NOT OVER TIGHTEN.
2.Assemble the supplied Female Flexi connector from the side entry inlet valve to the 1/2" BSP
inlet Stand Pipe located in the cistern tank.
3.From the underside of the pan connect the 1/2" BSP Female flexi connector to the bottom
of the stand pipe and feed the other end of the left or right hand side pan hole dependant on
which side the mains pressure inlet is located.
4.Slide Pan and cistern into place following points 8 & 9 in the pan installation section.
5.Connect the flexible hose to the water control valve.
6.Place cistern lid on top of the cistern and check push button workability.
7.Assemble the seat using the seat assembly instructions supplied in the seat box.
Run a bead of plumber grade silicone around the pan and up the edge of the wall to finish off.
Back Entry Only:
1.With the pan in place locate the cistern on to the pan with the sponge gasket placed
on the cistern outlet valve tail and connect the tank to pan using attachment bolts. Ensure that
NA369C-1P&NA369C-2C&NA5011 Installation Instructions