Progress Lighting UC9051GTX Installation & Operating Instruction

INSTALLATION & OPERATING INSTRUCTION FOR
UC9051GTX , UC9051TX 2631, 2632
Nia REMOTE FOR FAN WALL CONTROL
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
PROGRESS
NOTE: The frequencies on your Receiver and Transmitter have been preset at the factory. Before installing the Receiver,
make sure the dip switches on the Receiver are set to the same position on the Transmitter.
(Fig. 1) The Dip switches on the Transmitter are located on one side of the control.
1. SAFETY PRECAUTIONS:
e WARNING: HIGH VOLTAGE: Disconnect source of electrical power by removing fuse or switching off circuit breakers.
e Do Not use with solid state fans.
e Electrical wiring must meet all local and national electrical code requirements.
e Electrical source and fan must be 115/120 volt, 60 Hz. Maximum fan motor amps; 1.0 Maximum light watts; 300-incandescent only.
e Household electrical power can cause serious injury or death.
NOTE: BEFORE YOU BEGIN THE INSTALLATION OF YOUR NEW REMOTE CONTROL, MAKE SURE THE FAN IS
SET TO THE HIGHEST SPEED.
2. INSTALLING THE RECEIVER (FIG. 2)
a. Remove ceiling fan canopy from mounting bracket.
b. Disconnect existing wiring between ceiling fan and supply wires from junction box.
CONNECTING THE RECEIVER : Using the wire connectors provided, make the electrical connections as follows:
. Connect Green wire from fan to Bare copper (ground) from junction box.
. Connect Black wire (AC IN L) from Receiver unit to the Black wire from junction box.
. Connect White wire (AC IN N) from Receiver unit to White wire from junction box.
. Connect White wire (TO MOTOR N) from Receiver unit to White wire from fan.
. Connect Black or Red wire (TO MOTOR) from Receiver unit to Black or Red wire from fan.
Connect Blue wire (FOR LIGHT) from Receiver unit to Blue wire from fan. If other fan or supply wires are
different color, consult or have a qualified electrician do the installation.
. After wires are connected, carefully tuck them into junction box.
. Lay the black antenna wire on top of the Receiver unit, and insert into mounting bracket.
i. Reinstall the canopy on to mounting bracket.
+ D © O OU © w
"a Q
4. CONNECTING THE TRANSMITTER: Remove wall plate, disconnect and remove the toggle switch from wall junction box.
Using the wire connectors provided, make electrical connections to the new Transmitter unit as shown in (Fig. 2).
If your outlet box has a ground wire (green or bare copper) connect the wall transmitter's ground wire to it; otherwise
connect the wall transmitter's ground wire directly to one of the screws from the outlet box.
Carefully tuck connections inside wall switch box. Secure Transmitter with the two screws (provided). Attach wall plate
over control unit with (2) screws previously removed (Fig. 3).
5. OPERATING THE TRANSMITTER
a. HI, MED and LOW buttons: These three buttons are used to select the fan speed. Press and release the button
of desired speed setting; HI = Highest speed; MED = Medium speed; LOW = Lowest speed
b. "LIGHT" button: This button will turn the light ON or OFF and will also control the brightness setting. Press and
release the button and the light will turn ON or OFF. Press and hold the button for the desired brightness. The light
will cycle continuously between bright and dim settings as long as the button is held down. The light key has auto
resume, it will stay at the same brightness as the last time it was turned off.
c. "FAN OFF" This button will turn the fan off.
d. "REV" This button will change rotation direction.
e. Memory function
If turn off fan or light by wall control, it will memorize and recover automatically to last time's fan speed and light
brightness when turned on the next time.
f. This remote control unit is equipped with 16 code combinations, to prevent possible interference from other
remote units such as garage door openers, car alarm or security systems. If your fan or light kit go on and off
without using your remote control, simply change the combination code in your Transmitter and Receiver.
The installation of your remote control is complete, restore power to junction box.
6. TROUBLE SHOOTING GUIDE
Q. Fails to operate.
A. Make sure all connections on Receiver and Transmitter are done correctly and that there are no loose wire connections.
Make sure fan pull chain is set to the highest speed. Make sure code switches on Receiver and Transmitter are set to the same code.
CAUTION: Ceiling Angle Shall Not Exceed 30 Degrees, For Mounting Controller, Models UC-7067 or UC-7068.
PAGE 1 OF 4 SPEC.NO. 93009084 08/25/11