Advertisement
Available languages
Available languages
Quick Links
PACKAGE CONTENTS
A – Well Lights x 1
Assembly and Installation
1
Buried the housing
NOTE
Do not use a hammer. If the ground is hard, use water to
:
soften it or a trowel to loosen the soil.
The well lamp (A) is pre-installed in housing (B), and it is need to use
□
a screwdriver to lift out the plastic plug (D) and screw out the cover
screw (E) to release the housing (B).
Choose a location to buried the housing (B) into the ground.
□
It is necessary to ensure that the wires are placed inside the housing
□
(B) to connect the power supply.
C – Wire Connector x1 (with 12 in.
B – Housing x 1
wire attached to lamp body)
LED LOW VOLTAGE WELL LIGHT
D– Plastic plug x 4
2
Connecting the wires
WARNING: The wire connector (C) contacts have sharp edges for
piercing the main low voltage cable. To avoid injury, do not touch
the metal contacts.
CAUTION: The wire from low voltage power unit should be 12-16
AWG type underground low Energy Circuit Cable.
IMPORTANT:
Protect the wiring by routing it in close proximity to the light
□
fitting, or next to a building structure such as a house or a
deck.
The landscape wire and connector can also be hidden under
□
stone or buried under grass at a maximum depth of 6 in.
(15.24 cm).
Do not install the fixture within 10 ft. of a pool, spa, or fountain.
□
Do not submerge the fixture in water.
□
Place the wire connector (C) on opposite sides of the low voltage
□
cable (sold separately) from the transformer (sold separately)
where the fixture will be located.
Align and fit the main low voltage cable vertically to the slot of the
□
wire connector (C).
Press the wire connector (C) together until it is locked around the
□
main low voltage cable. The pre-set prongs will pierce the cable
insulation and establish contact with the electrical wire inside.
Once the wire connector (C) is in place, wrap it with electrical tape
□
(sold separately).
After all fixtures are installed, turn on the transformer.
□
1
Item # 1008 556 345
Model # LBW5401LX-02
Use and Care Guide
E – Cover Screw x 4
Advertisement
Summary of Contents for HAMPTON BAY LBW5401LX-02
- Page 1 Item # 1008 556 345 Model # LBW5401LX-02 Use and Care Guide LED LOW VOLTAGE WELL LIGHT PACKAGE CONTENTS C – Wire Connector x1 (with 12 in. A – Well Lights x 1 B – Housing x 1 wire attached to lamp body) D–...
-
Page 2: Care And Cleaning
Assembly and Installation(continued) Lock the well lamp into the housing Position the wire connector (C) and the electrical wires back □ inside the housing (B). Place the well light (A) into the housing (B), align the holes □ of the well light (A) with the holes of the housing (B) Screw the cover screws (E) into the holes to fasten the well □... -
Page 3: Cable Selection
Cable Selection 12 VOLT TAP Cable Length Total Fixture Wattage 0-50 feet 51-100 feet 101-150 feet 0-60 Watts 16 AWG 16 AWG 14 AWG 61-120 Watts 16 AWG 14 AWG 12 AWG 121-180 Watts 14 AWG 12 AWG Not Recommended 181-240 Watts 14 AWG 12 AWG... -
Page 4: Montaje E Instalación
Artículo # 1008 556 345 Modelo # LBW5401LX-02 GUÍA DE USO Y MANTENIMIENTO LUZ DE POZO LED DE BAJO VOLTAJE CONTENIDO DEL PAQUETE C – Conector de Cables (con cable de 12 pulgadas. Tapón de plástico x 4 E – Tornillo de tapa x 4 A –... - Page 5 Montaje e Instalación (continuado) Bloquear la luz de pozo en la carcasa Coloque el conector de cable (C) y el cable de nuevo en la carcasa □ (B). Coloque la luz del pozo (A) en la carcasa (B) y alinee el agujero de □...
-
Page 6: Advertencia De La Fcc
Selección por Cable GRIFO 12 VOLTIOS Longitud del Cable Total Fixture Potencia 0-50 pies 51-100 pies 101-150 pies 0-60 Watts 16 AWG 16 AWG 14 AWG 61-120 Watts 16 AWG 14 AWG 12 AWG 121-180 Watts 14 AWG 12 AWG No Recomendado 181-240 Watts 14 AWG...