Air King 3LY41/8540 Operating Instructions

OPERATING INSTRUCTIONS
OSCILLATING CERAMIC HEATER
with REMOTE CONTROL
MODEL 3LY41/8540
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
WARNING: USE OF A THREE-PRONG TO TWO-PRONG
ADAPTER IS NOT RECOMMENDED. IMPROPER CONNEC-
TION MAY CREATE THE RISK OF ELECTROCUTION. USE
OF SUCH ADAPTERS ARE NOT PERMITTED IN CANADA.
6. Where possible, avoid the use of extension cords because
7. Do not operate any Heater with a damaged cord or plug or
DESCRIPTION
The AirKing Oscillating Ceramic Heater features 2 heat settings
and a fan only setting. The heater oscillates 120° and comes with
8. Unplug power cord before servicing or moving the Heater.
a remote control for convenience. This unit also features a built in
timer to allow up to 7.5 hours of operation before automatic shut-
WARNING: DO NOT DEPEND ON THE ON/OFF SWITCH AS
down and comes with a 6ft. (1.82m) 16/3 grounded cordset.
THE SOLE MEANS OF DISCONNECTING POWER WHEN
SPECIFICATIONS
SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG
Motor ............................ 120 V/60 Hz
THE POWER CORD.
Control ......................... Manual/Remote
9. Do not insert or allow fingers or foreign objects to enter any
Settings ........................ High and Low Heat; Fan only
Air Flow Distribution ..... 120˚
Approvals ..................... UL/CUL listed. Close mesh
blower guard meets OSHA requirements.
10. To prevent a possible fire, do not block air intakes or ex-
MODEL 3LY41/8540
SETTINGS HIGH LOW FAN
11. Always place the Heater on a stable, flat, level surface when op-
BTU 5118 3070 Ø
Amps 12.5 7.0 0.288
Watts 1500 900 33.4
dB A 47 <40 47
12. This Heater is hot when in use. To avoid burns, do not let
GENERAL SAFETY INFORMATION
1. Use this Heater only as described in this manual. Any
other use not recommended by the manufacturer may
cause fire, electrical shock, or injury to persons.
13. A Heater has hot and arcing or sparking parts inside.
2. This Heater is intended for GENERAL USE ONLY.
3. Make certain that the power source conforms to the elec-
trical requirements of the Heater.
4. Extreme caution is necessary when any Heater is used
14. This Heater is not intended for use in wet or damp locations.
by or near children or invalids and whenever the Heater is
left operating unattended.
5. The power cord is equipped with a three-prong grounded
plug that must be inserted into a matching receptacle. Un- 15. Do not use Heater outdoors.
WARNING: REDUCE THE RISK OF FIRE OF ELECTRIC
der no circumstances must the grounding prong be cut
SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID
off the plug. Where a two-prong wall receptacle is en-
STATE SPEED CONTROL DEVICES.
countered, it must be replaced with a properly grounded
Rev. A 4/03 1
three-prong receptacle, installed in accordance with the Na-
tional Electrical Code (NEC) and all applicable local codes
and ordinances. This work must be done only by a quali-
fied electrician, using copper wire only.
the extension cord may overheat and cause a risk of fire. If
they must be used, minimize the risk of overheating by en-
suring that they are CUL/UL listed, a minimum No. 14 AWG,
rated not less than 1875 watts and of proper length. Never
use a single extension cord to operate more than one Heater.
after the Heater malfunctions, has been dropped or damaged
in any manner. Return Heater to authorized service facility for
examination, electrical or mechanical adjustment or repair.
Always unplug Heater when not in use.
ventilation or exhaust opening as it may cause an electric
shock or fire, or damage the Heater. Do not block or tamper
with the Heater in any manner while it is in operation.
haust in any manner. Do not place on soft surfaces, like a
bed, where openings may become blocked.
erating, to avoid the chance of the Heater overturning. Locate
the Power Cord so the Heater or other objects are not resting on
it. Do not run Power Cord under carpeting. Do not cover Power
Cord with throw rugs, runners, or the like. Arrange Power Cord
away from room traffic and where it will not be tripped over.
bare skin touch hot surfaces. Always use handle when
moving this Heater. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes and curtains at
least 3 feet (0.9 m) from the front of the Heater and keep
them at least 1 foot (0.3 m) from the sides and rear.
It
must NOT be used in potentially dangerous locations such
as flammable, explosive, chemical-laden or wet atmo-
spheres. Heater is intended for general use ONLY.
Never locate a Heater where it may fall into a bathtub or
other water container.
8540ESF
MODEL 3LY41/8540
OPERATION
Control Panel: (Figure 1)
1. When the heater is plugged in there will be a "beep"
to indicate that there is power to the unit.
2. ON/FUNCTION button. When this button is pushed,
HIGH indicator light comes on and heater is in the
high heat mode. (1500 watts)
3. Press the ON/FUNCTION button again the HIGH
indicator light goes off and the LOW indicator light
comes on and the heater is now in the low heat
SAFETY FEATURES
mode. (900 watts)
4. Press the ON/FUNCTION button again and the LOW
1. A Tip-Over Switch is built into the unit to prevent opera-
indicator light goes off and the FAN indicator light
comes on and the heater is in fan only mode.
2. A Thermal Overload Protector and a Thermal Fuse are
5. OFF button – Press this button will shut the
heater off.
3. A In-Line Fuse is built into the unit to prevent operation
6. "TIMER" button. Press it once and the light comes
on indicating 1/2 hour of time. Press it again and the
MAINTENANCE
light indicates 1 hour. Press it a third time and it indi-
WARNING: ALWAYS UNPLUG THE CORD BEFORE
cates 1.5 hours. The total time that can be indicated
MOVING OR SERVICING.
at one time is 7.5 hours. Continuing to press the timer
button will cycle through the settings until all timer DO NOT IMMERSE HEATER IN WATER.
lights are off. When the time indicator lights are off,
CLEANING: Clean the filter net at least once a month, more
the heater will run continuously.
often if dirty. A dirty filter could restrict the air flow and
7. The "SWING" button. Press this button and the swing
cause the Heater to function improperly or shut down.
light comes on and the heater will oscillate back and
Do Not Attempt To Remove Inlet Grill From The Heater.
fourth a full 120 degrees. Press it again and the light
1. Unplug the Heater from power source.
will go out and the oscillation will stop.
2. Vacuum Rear Grill area of Heater with Vacuum Brush
8. The heater must be placed flat on the floor or the tip-
over switch will shut it off automatically.
9. To disconnect Heater, press "ON/OFF" button, then
remove plug from outlet
3. Clean the body with a soft cloth. (NEVER USE ALCO-
CONTROLS
2 4 L H
1
Fan
0.5
ON
TIMER
SWING
FUNCTION
OFF
Figure 1
Remote Control: (Figure 2)
1. Press the ON-HIGH or ON-LOW button will start the
heater on either HIGH or LOW heat.
2. The OFF, TIMER and SWING buttons function in the
exact same manner as listed in steps 5 through 7 of
the operating instructions listed above.
3. The remote control is powered by two AAA batteries
supplied. There is a cover on the back of the remote
control that can be removed for replacement of the STORAGE: Store the Heater with these instructions in
batteries as required.
the original carton in a cool, dry place.
Rev. A 4/03 2
Figure 2
tion if the Heater is tipped over.
built into the unit to prevent overheating.
in the event of an overload.
Attachment to remove lint and dirt from internal filter.
DO NOT ATTEMPT TO TAKE HEATER APART (Figure
3). Do not remove grill guard or allow Heater to be oper-
ated without grill guard in place.
HOL OR SOLVENTS.)
Vaccum Brush
Attachment
Handle
Air Inlet
Opening
Filtering Net
(Inside)
Figure 3 Plug
8540ESF