Flexzilla L8651FZ Owner's Instructions

Owner's Instructions
Part No. : L8651FZ & L8654FZ
Flexzilla Portable Manual Open Face Air Hose Reel
®
CAUTION: Inspect hose before each use. Do not exceed 300 psi work-
ing pressure. Do not kink, twist, knot or abrade hose. Do not wrap hose
around body. Keep hose away from hot surfaces and/or chemicals. Keep
children away from work areas.
CAUTION: Read all instructions and warnings before operating this
product.
SAVE THESE INSTRUCTIONS! READ AND UNDERSTAND ALL
INSTRUCTIONS!
CARTON CONTENTS:
• Hose Reel assembly
• Curved carry handle and grip (2 medium bolts/nuts)
• Support legs (4 long bolts/nuts)
• Flexzilla ® air hose
• Lead-in hose
• Inlet swivel
• Swivel (to connect lead-in hose)
• Swivel handle (bolt & nut, for winding lever)
• Hose stopper (2 small bolts/nuts)
• Hose layering guide
• Hose layering bracket (4 small bolts/nuts)
ASSEMBLY:
SEE PAGE 2 for full assembly instructions
Female inlet
swivel fitting
Hose Layering
Bracket
Hose
Layering
Guide
Bend
Restrictor
3. BENCH, WALL, OR TRUCK MOUNTING: For mounting to wall or
bench surface, mount reel using the four outer holes in the mounting
base. Mounting fasteners not included. Reel can be mounted to truck
with or without support legs.
4. MOBILE USE: Fasten the support legs so the shorter end of each leg
is toward the back of the reel.
• Use four short bolts (included). Insert bolts first through the
recesses on bottom of support legs, then through outer pair of
holes in reel mounting base. Secure with lock nuts.
• Use two long bolts (included). Insert bolts through handle bolt
holes and then through center holes in mounting base. Secure
with lock nuts.
• Fit cushion grip to free end of carry handle.
FLEXZILLA, the color CHARTREUSE and the Flexzilla Stylized X are all registered trademarks of Weems Industries, Inc.
FLEXZILLA et la couleur CHARTREUSE et la Flexzilla Stylized X sont toutes des marques déposées de Weems Industries, Inc.
Legacy Manufacturing Company
Marion, IA 52302 USA
Carrying
Handle
Swivel Handle
Handle Arm
Mounting Bracket
Support Legs
Figure A
Ph: 319.373.7305
5. USING GROUND STAKES: (Stand-alone position)
• Four large holes are provided at the ends of the support legs
for use with ground stakes (not included) to reduce movement
when placing reel on ground.
OPERATION:
HOSE LAYERING GUIDE: Using the hose layering guide will help
reduce hose tangles by distributing the hose evenly during hose
rewinding. Place one hand on the hose layering guide and slide it
back and forth while retracting the hose.
FOR WALL OR OVERHEAD INSTALLATION :
1. Change the layering guide bracket position by removing the two
bolts where the layering guide bracket bolts to the side of the
mounting base. (See figure above)
2. Reattach the layering guide bracket using the same bracket end
hole and the third hole in the side of the mounting base. Tighten
bolts securely.
The hose layering guide may be removed if desired by removing
the hose stopper and retracting hose through the layering guide.
Replace the hose stopper on the hose.
Repair Parts Description
L8654FZLI 5' x 1/4" Lead-in hose for L8654FZ Reel
L8651FZLI 5' x 3/8" Lead-in hose for L8651FZ Reel
RP004068 Swivel body assembly for hose
service@legacymfg.com
legacymfg.com
(Published 2014-12-02 Revised 2023-06-29)
INS8651FZ