Datalogic ID-NET QL Series Instructions

QL300 / QL500
Quick Link ID-NET™ Connectors
DESCRIPTION
The QL series ID-NET™ connectors provide a fast and efficient way to
cable an ID-NET™ network using standard cables. The QL300/500s are
typically Master ID-NET™ connectors designed to be used with the
QL100/150/200s ID-NET™ Slave connectors.
The QL300 is a passive connection module which can be used in
Standalone or ID-NET™ Master Multidata, Slave Multidata or Master
Synchronized layouts. It provides separate ports for Power Supply,
External Trigger, Digital I/O and Communication. Host communication is
provided through connectivity to the reader Main serial interface
(RS232/485) or Aux RS232 serial interface.
ID-NET™ network and power supply signals are sent out to the next
connected device by means of a dedicated port, however input power is
not received from the network. Therefore each QL300 must be powered
separately.
The QL500 is an active connection module which can be used in
Standalone or ID-NET™ Master Multidata, or Master Synchronized
layouts. It provides separate ports for Power Supply, External Trigger,
Digital I/O and Communication. Host communication is provided through
the integrated Ethernet module which connects internally to the reader's
Main serial interface. Reader Aux RS232 serial interface is also provided.
ID-NET™ network and power supply signals are sent out to the next
connected device by means of a dedicated port, however there is no
network input connector and therefore it cannot be used as an ID-NET™
Slave.
The QL series are compatible with the following readers:
DS2100N DS4800 Matrix 400™
DS2400N Matrix 200™
QL300
QL500
821001641 (Rev. A)
CONNECTIONS
ID-NET Out
M12 5P Female (A-coded)
Pin Function
1 Shield
2 Vdc
3 GND
4 ID+
5 ID-
QL300 only (ID-NET In)
M12 5P Male (A-coded)
Pin Function
1 Shield
2 nc
3 GND
4 ID+
5 ID-
QL500 only (Ethernet)
RJ45 8P Female
Pin Function
1 TX+
2 TX-
3 RX+
P8 P1
6 RX-
4, 5, 7, 8 nc
OVERALL DIMENSIONS
129
[4.56]
45
42
[1.49] [1.59]
QL300
129
[4.56]
42 45
[1.49] [1.59]
QL500
Power
M12 3P Male (B-coded)
Pin Function
1 Earth
2 Vdc
3 GND
Trigger
M12 4P Female (A-coded)
Pin Function
1 +V
2 nc
3 -V
4 I1+
MOUNTING
There are two self-threading screws provided for mounting the QLs to
various wooden or plastic surfaces. Mounting to other surfaces such as
concrete walls or metallic panels requires user-supplied parts (screws,
screw anchors, nuts, etc). Keep in mind that the connected reader must
have its Chassis grounded to Earth, see paragraph "Grounding".
QLs can also be mounted to a Bosch Frame using the BA200 mounting
accessory.
The distance between mounting bushings is given in the overall
dimension diagram for each QL.
IP65 protection is provided when the cables (or QLs)
are properly mated.
NOTE
GROUNDING
There are two general rules to follow regarding network grounding:
1) The network Shield must only be connected to Earth ground at
one point (the Master).
When using isolated power supplies, Earth grounding can be
mm
accomplished through the CAB-PW-EXT accessory cable and the
in
BA400 or QL300/500 Power connector.
CAB-PW-EXT
Power Supply
Earth ground connection
2) All reader Chassis must be connected to Earth ground.
All the readers in the network must have their Chassis connected to
Earth ground either by: mounting to conductive metal brackets or
frames which are connected to Earth ground; or through the CBX or
SC4000; or through the QL bushing.
In the case of grounding through the CBX or SC4000, connect the
Earth signal to a good earth ground and set the internal Chassis
jumper to Earth.
In the case of grounding through the QL bushing, connect a flying
lead from the mounting bushing to an Earth ground. The mounting
bushing is internally connected to the reader Chassis.
mm
in
13
Reader
25P D-Sub Female
Pin Function
1,
shell, Reader Chassis
both bushings
2 TXM
3 RXM
4
RTSM *
5 CTSM *
6 I2A
7 GND
8 O1+
9 nc
10 I2B
11 O2+
12 O2-
13 Vdc
* pins 4 and 5 are nc for QL500.
I/O Port
15P HD D-Sub Female
Pin Function
1 O1+
2 TXA
3 RXA
4 RXM *
5 CTSM *
6 O1-
7 Vdc
8 O2+
* pins 4, 5, 12 and 15 are nc for QL500.
Do not connect GND and SGND to different (external)
ground references. GND and SGND are internally
connected through filtering circuitry which can be
permanently damaged if subjected to voltage drops over
0.8 Vdc.
CAUTION
ACCESSORIES
Description
QL300
Power
Cables
CAB-PW-EXT M12 POWER
EXTENSION CABLE
CBL-1480-01 THIN M12/5P
MALE/FEMALE 1M
CBL-1480-02 THIN M12/5P
MALE/FEMALE 2M
CAB-AUX04 15P DSUB TO DB9
SERIAL CABLE 3M
Terminators
CBL-1490 TERM. RESIST.
THIN M12/5P/MALE
CBL-1496 TERM. RESIST.
THIN M12/5P/FEMALE
Field Mountable Connectors
FMC400 M12 3P F. CONN. POWER
Mounting
BA200 Bosch Adaptors
The FMC accessory connectors can be used to make custom External
Power and Service cables in case the standard cables don't satisfy the
application requirements.
1
25 14
Pin Function
14 nc
15 nc
16 nc
17 nc
18 I1A
19 GND
20 RXA
21 TXA
22 O1-
23 ID+
24 ID-
25 GND
5 1
10 6
15 11
Pin Function
9 I2A
10 O2-
11 I2B
12 TXM *
13 GND
14 SGND
15 RTSM *
Part Number Connection
93A051381 Power
970101021
ID-NET Out/In
970101022
93A051386 I/O Port
970101069 ID-NET Out
970101082 ID-NET In
93ACC1884 Power
93ACC1822