Lightware PSU2x10-200-12V Quick Start Manual

Quick Start Guide
PSU2x10-200-12V
PSU2x10-200-5V
PSU2x20-400-12V
PSU2x20-400-5V
Introduction
Thank you for choosing Lightware's rack mountable power supply. The units are all housed in
a 1U high solid metal rack enclosure for durability and easier mounting. 5V and 12V DC output
versions are also available with 10 and 20 output connectors. Several protections are built in
like short circuit, overload, over voltage, over temperature which features make these PSUs
really trustful. The units are designed to supply devices made by Lightware.
 The cover picture of this document is an illustration. The PSU2x series devices are built with
2 pcs rack ears on the front side by default.
Box Contents
Power supply unit with IEC power cable Safety and Warranty Info,
rack ears (2x) Quick Start Guide
 Please note that DC-DC power cables are not supplied with the product.
Compatibility
The following table contains those Lightware products that are compatible with the power
supplies and also the technical data of the DC plug:
PSU2x10-200-5V, PSU2x20-400-5V
DC plug Compatible Lightware products
Power supply Device Type
DVI-OPT-110 series
1.35 / 3.5 mm
DP-OPT 150 series
DVI-HDCP-OPTS 90 series
USB Micro-B
DVI-HDCP-OPTM 90 series
EDID Manager V4
HDMI-, DVISL- and DVIDL extenders
DA2DVI-HDCP-Pro
2.5 / 5.5 mm
DA2DVI-DL
DA2HDMI 4K-Plus series
2.5 / 5.5 mm DP-OPT 100 series
DVI-TP series
HDMI-, UMX- and DVIDL-OPT series
HDMI 4K series
SW4-OPT-TX240RAK
Remote control panels
Front and Rear View
1
2 3
Power LED Power LED lights green when the unit is powered on.
1
AC connector Standard IEC power connector. Accepts 100 to 240 Volts,
2
50 or 60 Hz power sources.
Power switch The power supply can be switched ON/OFF with this switch.
3
4 DC connectors Locking DC connectors for the appliances that are desired
to supply.
Connecting Devices
1. Place the power supply unit in the rack and fix it by screws with the mounting ears.
2. Connect the DC cables to the power supply and to the extender units.
3. Connect the AC power cable to the power supply.
4. Switch on the appliance.
 Please note that fixing screws and DC power cables are not supplied with the appliance.
 If the power supply cannot be switched on, please check the IEC power cable, the AC
mains and the fuse at the AC connector on the back of the unit. If the LED on the front panel
does not light up at all, the unit is most likely damaged and further use is not advised. Please
contact support@lightware.com.
Locking DC Connectors
DC cables from Lightware contain locking DC connector that establishes robust and safe
power connection. After plugging it in, turn the plug clockwise as shown on the picture:
 Do not forget to turn the plug counterclockwise before trying to disconnect the cable.
PSU2x10-200-12V, PSU2x20-400-12V
DC plug Compatible Lightware products
Power supply Device Type
DP-TPS-200 series
DVI-HDCP-TP-50 and -100 series
DVI-HDCP-TPS-90 and -210 series
HDMI-TPS-TX-200 series
HDMI-TPS-90-95-97 series
HDMI-TPS-RX110AY
2.1 / 5.5 mm 2.1 / 5.5 mm HDMI-TP-50, -100 and -200 series
UMX-TP series
UMX-TPS-TX100 series
TPS-TX200 series
MMX4x2-HT200
MMX4x2-HDMI
SW4-TPS-TX240
 Cables are available at Lightware, please contact sales@lightware.com.
4
 The main differences among the variants are the number of the DC connectors and the
voltage range; PSUx20-400-12V can be seen on the photos.
Assembly of the Rack Ears
Two rack ears are supplied with the product, which are fixed on the left and right side with 8 pcs
M4 screws. The ears are removable and can be re-assembled to another position or direction.
 M4x8 size is the longest allowed screw for fixing the ears to the housing. Using
different (e.g. longer) screws may cause damage to the device.
Mounting with Rack Ears
The rack ears allow mounting the device as a standard rack unit installation.
1A DC PIN: 2mm 1A DC PIN: 2mm
 Always use all the four screws for fixing the rack screw
device ears to the rack rail. Choose properly flat washer
device
sized screws for mounting. Keep a minimum of
mounting ear
two threads left after the nut screw.
rack rail
cage nut
Ventilation
 To ensure the correct ventilation and avoid
overheating, leave enough free space around the
appliance. Do not cover the appliance, leave the
ventilation holes free on both sides.
min. 2
threads left
Specifications
General
Compliance ....................................................................................................CE, UKCA
Electrical safety .................................................................................. EN 62368-1:2014
EMC compliance (emission)..................................................................EN 55032:2015
EMC compliance (immunity) .................................................................EN 55035:2017
RoHS compliance ..................................................................................EN 63000:2018
Warranty ............................................................................................................. 3 years
Operating temperature ...................................................... 0 to +55°C (+32 to +122°F)
Operating humidity ......................................................... 10% to 90%, non-condensing
Cooling .............................Fan (2 pcs., 40 mm diam.), air flows right to left (front view)
Protection against .............. Short circuit / Overload / Over voltage / Over temperature
Connectors
AC power connector ....................................................................... IEC C14 receptacle
DC power connector (5V version) ........................... locking DC connector, 2.5/5.5 mm
DC power connector (12V version) ......................... locking DC connector, 2.1/5.5 mm
Power
Power supply option ....................................................................................built-in PSU
Supported power source .........................................................100-240 V AC; 50/60 Hz
AC fuse ...................................................................................................................F 5 A
PSU2x10- PSU2x20- PSU2x10-
Models
200-5V 400-5V 200-12V
DC output number 10 20 10
Nominal power 200 W 400 W 200 W
DC output voltage 5V 12V
Rated current per
2.5A 1.1A
output port
Heat dissipation
683 1365 683
(max.)
Enclosure
Rack mountable ......................................................................................... Yes, 1U high
Enclosure material ........................................................................................ 1 mm steel
Dimensions in mm ........................................................... 482* (446)W x 182D x 43.9H
Dimensions in inch .............................................................. 19* (17.6)W x 7.2D x 1.8H
Net Weight (PSU2x10-200 series) .......................................................2870 g / product
Net Weight (PSU2x20-400 series) .......................................................3430 g / product
* with rack ears
TAKE CARE OF ME
I AM THE ONE AND ONLY
USER DOCUMENT FOR
THIS PRODUCT
Lightware Visual Engineering PLC.
Budapest, Hungary
sales@lightware.com +36 1 255 3800
 
support@lightware.com +36 1 255 3810
 
©2023 Lightware Visual Engineering. All rights reserved. All trademarks mentioned are the
property of their respective owners. Specifications are subject to change without notice.
Further information on the device is available at www.lightware.com.
Doc. ver.: 1.5
19210073
PSU2x20-
400-12V
20
400 W
1365