Advertisement
Quick Links
V
ECTOR
SCC-T1-Tp2 Temperature transmitter for PT1000 probes
Features
•
Precision temperature measurement for different ranges and
accuracies
•
Minimum and maximum value memory
•
0...10V, 0...20mA or 2...10V, 4...20mA measuring signals,
selectable with jumpers
•
Optional alternative signal ranges programmable
Selectable averaging signal
•
Optional LCD display (OPC-S) or external display (OPU-S)
•
Status LED
•
Applications
•
For indoor, outdoor, duct, immersion temperature
measurement for heating, ventilation and air conditioning
applications
•
Recording of minimum and maximum values for critical environments
•
Supervision of critical temperatures
Temperature transmitter
The transmitter measures the temperature for a PT1000 platinum film element. The transmitter does not include the
PT1000 sensor. An external PT1000 according to EN 60751 has to be connected for the transmitter to operate.
The microprocessor samples the temperature once per second. It calculates an averaging signal over a preset number of
seconds and generates an output signal based on lower and upper signal range values. Standard range is
-40...400°C (-40...752°F) and 1 second's average.
The output signal range and type may be customized by jumpers and if required by a programming tool. Standard signal
ranges are 0-10VDC, 2-10VDC, 4-20mA and 0-20mA. These ranges can be set by jumpers. Other ranges can be set on the
–OP transmitter or by connecting OPU-S.
Minimum and maximum values
By using a display module (-OP or OPU-S), the user has the option to read out and reset minimum and maximum values.
The minimum and maximum values may as well be used as output signals. The minimum and maximum values are saved
into a non-volatile memory and are therefore available after a power interruption.
Types and Ordering
Part Name
Part No.
SCC-T1-Tp2
40-300075
SCC-T1-Tp2-OP
40-300076
Accessories
Part Name
Part No.
S-Tp2-2
40-200012
SD-Tp2-12-2
40-200024
SD-Tp2-20-2
40-200027
SDB-Tp2-12
40-200056
SDB-Tp2-20
40-200034
SRA-Tp2
40-200041
SOD-Tp2
40-200064
OPU-S
40-500030
AMC-1
20-100035
AMC-2
20-100067
Doc: 70-07-0175B, V1.0, 20210326
Subjects to alteration
Measuring Temperature Range
-40...400°C (-40...752°F)
-40...400°C (-40...752°F)
Description
Flying lead sensor, 2 m cable
Flying lead duct sensor; Probe length 12 cm, 2 m cable
Flying lead duct sensor; Probe length = 20 cm, 2 m cable
Duct sensor, Probe length 12 cm
Duct sensor, Probe length 20 cm
Indoor sensor
Outdoor sensor
External display module
Cable gland PG9 for cables 4 – 8 mm (AWG 6 – 1)
Conduit connector NPT 1/2
© Vector Controls LLC, USA
www.vectorcontrols.com
SCC-T1-Tp2(-OP) for PT1000 probes
Options
Includes display module OPC-S
Product Data Sheet
Page 1-6
Advertisement
Related Manuals for Vector SCC-T1-Tp2
Summary of Contents for Vector SCC-T1-Tp2
- Page 1 SCC-T1-Tp2(-OP) for PT1000 probes ECTOR Product Data Sheet SCC-T1-Tp2 Temperature transmitter for PT1000 probes Features • Precision temperature measurement for different ranges and accuracies • Minimum and maximum value memory • 0…10V, 0…20mA or 2…10V, 4…20mA measuring signals, selectable with jumpers •...
-
Page 2: Technical Specification
SCC-T1-Tp2(-OP) for PT1000 probes ECTOR Product Data Sheet Technical Specification Important notice and safety advice This device is for use as a temperature transmitter. It is not a safety device. Where a device failure could endanger human life and property, it is the responsibility of the client, installer and system designer to add additional safety devices to prevent such a device failure. -
Page 3: Installation
SCC-T1-Tp2(-OP) for PT1000 probes ECTOR Product Data Sheet Installation The transmitter should be installed, probe facing down, directly on the wall, in weather protected area. Turn the single screw on the cover counter clockwise and remove cover. Mark the location for the mounting holes on the wall. -
Page 4: Jumper Settings
SCC-T1-Tp2(-OP) for PT1000 probes ECTOR Product Data Sheet Jumper settings JP1 Signal type JP2 Signal range 2-10V 0-20mA, 4-20mA 4-20mA 0-10V 0-20mA 0-10V, 2-10V JP1 JP2 JP3/JP4 JP3/JP4 Sensor connection (Jumpers must match) 4-Wire connection STATUS Compensate wire resistance OPC-S... - Page 5 ECTOR Product Data Sheet Configuration of SCC-T1-Tp2-OP or SCC-T1-Tp2 In order to configure the SCC transmitter or access minimum and maximum settings either the SCC-T1-Tp2-OP has to be used or an OPU-S remote terminal need to be connected. Display and operation Legend: ...
- Page 6 SCC-T1-Tp2(-OP) for PT1000 probes ECTOR Product Data Sheet Smart Sensors and Controls Made Easy! Quality - Innovation – Partnership Vector Controls LLC 17, Francis J. Clark Circle Bethel, CT 06801 info@vectorcontrols.com www.vectorcontrols.com/ Doc: 70-07-0175B, V1.0, 20210326 © Vector Controls LLC, USA...