Nidac 2 Series Manual

™
PSR2
Prove Standard Proximity Card Reader
"Series 2"
FEATURES
•
Compatible with all NIDAC Presco controllers.
•
Outputs Presco and wiegand data.
•
Site code read from EM cards in wiegand mode is compatible with generic
EM wiegand prox readers.
•
Reads HID 125kHz cards.
•
Suitable for indoor usage only.
•
Audible and visual (buzzer & LED) feedback on card read.
•
12V DC operation.
•
17.5mm thin surface mounting with hidden screws.
•
Operating temperature range of 0ºC to 40ºC.
•
5 year manufacturer's warranty.
IMPORTANT DIFFERENCES BETWEEN THE PSR2 AND PSR16
•
When used in wiegand mode the site code read from EM cards is different.
To make the Prove PSR2 read the same site code as the Presco PSR16
refer to the "Wiegand EM Card Proximity Reader Options" section and set
memory 060 to 121.
•
Standard 26 & 37 bit HID cards can be read, other HID formats will read
but the output of some cards may not match that of an HID reader.
SPECIFICATIONS
Voltage: 9V to 14V D.C.
Current: 150mA max.
Operating Temp: 0C to 50C.
Weight: 150 grams.
Dimensions: 126mm x 80mm x 17.5mm (H x W x D).
Up to 20cm (8").
Read Range:
Excitation Freq: 125 ± 5 KHz.
Output: Presco DTA or wiegand, pulse width = 50s, pulse
separation = 2ms.
Wiring Distance: PSR2 to Presco PAC controller = 1Km using unshielded
cable, 100 max. return resistance on DTA line. To achieve
distances greater than 100m the PSR2 may require a
separate local power supply depending upon the thickness of
the cable used.
PSR2 to wiegand controller, shielded cable must be used.
Wire Gauge Distance Wire Gauge Distance
22 AWG 150m (490 ft) 26 AWG
24 AWG 100m (330 ft) 28 AWG
WIRES
There are 8 wires for the PSR2, not all will be needed for each installation. The
unused wires should always be terminated and left unconnected.
Black 0V (Ground).
Red +12V D.C.
White DTA (Presco data line) or D1 (Wiegand Data 1).
Green D0 (Wiegand Data 0).
Blue Blue LED control wire, +3V to +14V active.
Yellow Blue LED control wire, 0V active.
Brown Buzzer control wire, 0V active.
Orange Connect to 0V (black wire) on power up to enter option setting mode.
Drain Shield (in wiegand mode connect to earth/ground at controller).
INSTALLATION
1. Mark the location using supplied template and drill out required holes.
2. Remove the front fascia by inserting a wide flat bladed screwdriver into the
slot at the bottom of the unit and tilting the handle away from the front.
3. Attach the PSR2 to the wall using screws in the two oval mounting holes.
PSR2 TO PAC1 / PAC2
Programming Prox cards & tags into a PAC controller
To program a proximity card or tag into a PAC controller follow the same steps
as shown in the controller manual for programming a new user code. When it
comes to the stage to enter the user code simply present the card or tag to the
PSR2 that is connected to the same input as the programming keypad, or
alternatively enter the 9 digit code for the proximity card, note that this code may
contain star (*) and hash (#) symbols and leading zeroes (0) do need to be
entered.
PAC1 Programming Example
This example uses a PAC1 controller, programming a momentary operation
proximity card or tag into memory location 001.
1. Put the PAC1 into program mode using the management code or button on
the PAC1.
2. Using the Prove keypad connected to the PAC1, open the memory location
to store the Prox card in * 001 1 E
3. Present the proximity card or tag to the PSR2.
4. Take the PAC1 controller out of program mode.
60m (195 ft)
40m (130 ft)
PSR2 TO WIEGAND
To change the LED colour from red to blue apply a negative signal (0 to 2V) to
the Yellow wire or a positive signal (2.5 to 28V) to the Blue wire.
To sound the buzzer apply a negative signal (0 to 2V) to the Brown wire.
* If a fused output for readers is not provided use a 200mA inline fuse to protect
the power supply from short circuiting if PSC2 wires are tampered with.
PSR2 OPTIONS
There are several options that can be set to alter the way in which the PSR2
behaves. These options fall into the 3 categories of General, Presco and
Wiegand EM Card Proximity Reader, all of these are explained below.
General Options
These options set the functionality of the PSR2 independent of whether it is in
wiegand or Presco mode.
Memory Function
005 Force Presco or wiegand mode
200 Red LED brightness factor
201 Blue LED brightness factor
(1) - Force Presco or wiegand mode
101 = Always in Presco mode.
202 = Always in wiegand mode.
All other values = Mode auto detected using white wire.
(2) - LED brightness factor
The red & blue LEDs can have their brightness individually set
1 = LEDs are at lowest brightness.
20 = LEDs are at full brightness.
Default
(1)
255
(2)
10
(2)
10
[Memory 005]
[Memories 200 & 201]