Advertisement
Quick Links
Press POWER once to
POWER
turn on or off the
selected device.
Mode Keys for Access 3:
VCR
CBL
T V
DVD
SAT
ACCESS 3
Press VCR/DVD, TV, or
CBL/SAT once to select
UNIVERSAL REMOTE CONTROL
a home entertainment
device to control.
Use the keypad (0 ~ 9)
1
2
3
to directly select
4
5
6
channels (for example,
7
8
9
09 or 31).
0
Press MUTE once to
MUTE
turn sound off
or on.
Press PREV once to
PREV
recall the last-viewed
channel and to page
back one screen on the
main menu.
Press ENTER once
ENTER
after entering channel
numbers on some TV
models.
EXIT
Use MENU (or EXIT) to
MENU
choose options (or
exit) from your
selected device's
menu or guide.
USER'S GUIDE
Use VOL+ (or VOL-)
VOL – –
VOL +
to raise (or lower) the
sound volume.
Use CH+ (or CH -) to
SKIP FWD
CH
select the next higher
INTRODUCTION
(or lower) channel.
CH
The One For All Access 3 Universal
When controlling a
SKIP FWD
SHIFT
Remote Control is designed to operate
CH
DVD player, use SKIP
three home entertainment devices,
FORWARD to next DVD
CH
depending on the model purchased (see
chapter., use SKIP
SKIP REV
Key Charts, Mode Keys on the right).
REVERSE to the last
DVD chapter.
The remote control requires two fresh
AAA alkaline batteries (not included) and
Press SHIFT and use
SHIFT
easy programming to control your devices.
the Up/Down/Left
MUTE
For best results, please read and perform
Right cursor keys to
all instructions listed here.Also, keep
move the cursor in the
these instructions for future reference.
program guide and
menu screens.
FEATURES AND FUNCTIONS
Press SHIFT and MUTE
to select a menu item.
Use the Key Charts to learn how to use the
Press SLEEP to activate
universal functions of the One For All
SLEEP
your device's sleep
Access 3 Universal Remote Control.
timer (not available
Key Charts
for all devices).
Use SETUP for all
SET
Use the transport keys
REW
FF
PLAY
programming
to control your VCR,
sequences.
REC
PAUSE
STOP
CD or DVD player, or
VOD. To record a
The LED (red light)
program, press the
blinks to show that
record key (
the remote control is
working and is
sending signals.
INSTALLING BATTERIES
PROGRAMMING
TV/VCR COMBO CONTROL
1. On the remote control's back, push the
tab and lift off the battery cover.
Perform the following instructions to
control a TV/VCR Combo:
2. Obtain two (2) new AAA alkaline
batteries. Match the + and – marks
1. Turn on the TV/VCR Combo and
on the batteries to the + and –
insert a video cassette.
marks in the battery case, then insert
NOTE: Please read steps 2-4 completely
the new batteries.
before proceeding. Highlight or write down
the codes and device you wish to program
3. Press the battery cover back into
before moving on to step 2.
place. The tab should click when the
cover is locked.
2. On the remote control, press VCR.
Press and hold SETUP until the LED
4. Test the unit by pressing POWER
blinks twice, then release SETUP.
and any mode key (e.g., TV). If the
batteries are inserted correctly, the
3. Use the Setup Codes For TV/VCR
LED will blink once.
Combos (on the back side) to locate
the brand name and then enter the
NOTE: When batteries need replacement,
first four-digit code for your device.
the remote control will stop operating.
Remove the old batteries and insert new
If performed correctly, the LED will
ones within 10 minutes to ensure all of
blink twice.
your programming information is restored.
NOTE: If the LED did not blink twice, then
repeat steps 2 through 3 and try entering
the same code again.
PROGRAMMING
4. Aim the remote control at the device
DEVICE CONTROL
and press POWER once. It should turn
The One For All Access 3 remote control
off. If the device does not respond,
is preprogrammed at the factory to
repeat steps 2-3, trying each code for
operate an RCA TV and VCR, a Motorola
your brand until you find one that
(GI) cable box, and a Toshiba DVD play-
works. If it still does not work, try
er. To control devices other than the
Searching For Your Code.
default brands, perform the following
NOTE: If the device does not have a
steps; otherwise skip this section:
POWER key, press the
NOTE: For TV/VCR Combo control, see the
next section.
SEARCHING FOR YOUR CODE
1. Turn on a device (e.g.,VCR) and, if
applicable, insert media, (e.g.,
If your device does not respond to the
cassette or disc).
remote control after trying all codes
listed for your brand, or if your brand is
NOTE: Please read steps 2-4 completely
not listed at all, try searching for your
before proceeding. Highlight or write down
the codes and device you wish to program
code. For example, to search for a code
before moving on to step 2.
for your TV:
2. On the remote control, press a device
1. On the remote control, press TV once.
key once (i.e., VCR/DVD, TV, or
2. Press and hold SETUP until the LED
CBL/SAT ). Press and hold SETUP until
blinks twice, then release SETUP.
the LED blinks twice, then release
SETUP.
3. Enter 9 - 9 - 1. The LED will
blink twice.
3. Use the Manufacturer's Codes to
locate the type of device and brand
4. Aim the remote control at the the
name and then enter the first four-
TV and slowly alternate between
digit code for your component. If
pressing POWER and TV. Stop when
performed correctly, the LED will
the TV turns off.
blink twice.
NOTE: In the search mode, the remote
NOTE: If the LED did not blink twice, then
control will send IR codes from its library
repeat steps 2 through 3 and try entering
to the selected device, starting with the
the same code again.
most popular code first.
4. Aim the remote control at the device
5. To lock in the code, press and hold
and press POWER once. The device
SETUP until the LED blinks twice,
should turn off. If it does not respond,
then release SETUP.
repeat steps 2-3, trying each code for
6. To search for the codes of your other
your brand until you find one that
devices, repeat steps 1 through 5, but
works. If it still does not work, try
substitute the appropriate device key
Searching For Your Code.
for the device you are searching for.
•
) twice.
NOTE: If the device does not have a
POWER key, press the
( Play ) key.
5. Repeat steps 1 through 4 for each
device you want to control.
CHECKING THE CODES
VCR back to VCR:
If you have set up the remote control
DVD as 2nd TV key:
using the Searching For Your Code
procedure, you may need to find out
which four-digit code is operating your
DVD as 2nd CBL key: SETUP - 9 - 9 - 2
equipment:
For example, to find out which code is
DVD as 2nd SAT key: SETUP - 9 - 9 - 2
operating your TV:
1. On the remote control, press TV once.
DVD as 2nd VCR key: SETUP - 9 - 9 - 2
2. Press and hold SETUP until the LED
blinks twice, then release SETUP.
DVD back to DVD:
3. Enter 9 - 9 - 0. The LED will
blink twice.
When a re-assignment is done, the LED
4. To view the code for the first digit,
will blink twice to confirm your choice.
press 1 once.Wait 3 seconds, count
At that time, you will need to program
the LED blinks (e.g., 3 blinks = 3)
and write down the number.
the remote control for the new device
(see Programming Device Control).
NOTE: If a code digit is "0", the LED will
not blink.
CHANGING VOLUME LOCK
5. Repeat step 4 three more times for
The One For All Access 3 is set to
remaining digits. Use 2 for the
control the volume of your TV in the TV,
second digit, 3 for the third digit,
VCR, CBL/SAT, and DVD modes. If you
and 4 for the fourth digit.
want the volume to be controlled by a
mode other than TV (e.g., CBL/SAT),
6. To check for codes of other devices,
change the Volume Lock as follows:
repeat steps 1 through 5, but substi-
tute the appropriate device key for
To Change Volume Lock To
each device you are checking.
Another Mode:
As before, write down each four-
digit code.
1. On the remote control, press and
( Play ) key.
RE-ASSIGNING DEVICE KEYS
2. Enter 9 - 9 - 3 and then press any
The One For All Access 3 can be set to
control a second TV,VCR, or DVD player.
3. Now, whenever you press VOL+,
For example, to control two TVs, a VCR,
and a cable box, you will need to re-
assign the unused DVD key to operate
the second TV as follows:
Unlocking Volume Control:
1. On the remote control, press and
NOTE: Perform these instructions when you
hold SETUP until the LED blinks
want independent volume control for each
twice, then release SETUP.
programmed device (e.g., TV volume control
in TV mode, CBL/SAT volume control in
2. Enter 9 - 9 - 2. The LED will
CBL/SAT mode, etc.)
blink twice.
1. On the remote control, press and
3. Press TV once, then press DVD once.
4. The DVD key is now ready to be
programmed for your second TV.
2. Enter 9 - 9 - 3 and then press VOL+.
See Programming Device Control.
To re-assign other device keys, repeat
3. Volume will again be controlled
steps 1 through 4 by substituting the key
sequence from the below chart for the
most popular components:
TROUBLESHOOTING
To Re-Assign Key
Sequence
Perform
For assistance, please contact us in any
VCR as 2nd TV key:
SETUP - 9 - 9 - 2
of the following ways:
- TV - VCR
• Consumer Help Line: (330) 405-8612
VCR as 2nd CBL key: SETUP - 9 - 9 - 2
• Internet: http://www.oneforall.com
- CBL/SAT - VCR
VCR as 2nd SAT key: SETUP - 9 - 9 - 2
PROBLEM:
- CBL/SAT - VCR
VCR as 2nd DVD key: SETUP - 9 - 9 - 2
SOLUTION: Replace batteries with two
- DVD - VCR
SETUP - 9 - 9 - 2
PROBLEM:
LED blinks when you
- VCR - VCR
press a key, but home
entertainment component
SETUP - 9 - 9 - 2
does not respond.
- TV - DVD
SOLUTION: Make sure the remote
control is aimed at your
- CBL/SAT - DVD
home entertainment
device and is not farther
than 15 feet away.
- CBL/SAT - DVD
PROBLEM:
The unit does not control
home entertainment
- VCR - DVD
devices or commands are
not working properly.
SETUP - 9 - 9 - 2
- DVD - DVD
SOLUTION: Try all listed codes for the
component brands being
set up. Make sure they
can be operated with an
infrared remote control.
PROBLEM:
TV/VCR combo does not
respond properly.
SOLUTION: Use the VCR codes for
your brand. Some combo
units may require both a
TV code and a VCR code
for full operation.
PROBLEM:
Changing channels does
not work properly.
SOLUTION: If original remote control
required pressing ENTER
to change channels, press
ENTER on the remote
hold SETUP until the LED blinks
control after entering the
twice, then release SETUP.
channel number.
PROBLEM:
Tried "Search Method"
mode key once (except TV). The LED
and still could not find a
will blink twice.
working code.
SOLUTION: Clear the device key as
VOL–, or MUTE, volume will be
follows: Press and hold
controlled by your mode choice.
SETUP until the LED
blinks twice, then release.
Next enter 9 - 9 - 2. Then
press the device key to be
cleared twice. Now repeat
the "Search Method. "
PROBLEM:
CH and CH do not
work for your RCA TV.
hold SETUP until the LED blinks
SOLUTION: Due to RCA design (1983-
twice, then release SETUP.
1987), only the original
remote control will oper-
The LED will blink four times.
ate these functions.
PROBLEM:
Remote control does not
according to its default states.
turn on Sony or Sharp
TV/VCR Combo.
SOLUTION: For power on, these prod-
ucts require programming
TV codes. For Sony, use
TV code 0000 and VCR
code 0032. For Sharp, use
TV code 0093 and VCR
code 0048.
LED does not blink when
LIFETIME WARRANTY
you press a key.
One For ALL ("OFA") warrants this
product to be free from defects in mate-
new AAA alkaline batteries.
rials and workmanship, under normal
use, throughout the period of the prod-
uct's ownership by the original purchas-
er. This warranty does not cover damage
or failures caused by products or ser-
vices not supplied by OFA, or which
result from accident, misuses, abuse,
neglect, mishandling, misapplication,
faulty installation, set-up adjustment,
improper maintenance, alteration, mal-
adjustment of consumer controls, modi-
fications, commercial use, or that is
attributable to acts of God.
There are no express warranties except
as listed above. OFA SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSE-
QUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT
OR ARISING OUT OF ANY BREACH OF
WARRANTY,ALL EXPRESS AND
IMPLIED WARRANTIES, INCLUDING
THE WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE,ARE LIMIT-
ED TO THE WARRANTY PERIOD SET
FORTH ABOVE. Some states do not
allow the exclusion or limitation of inci-
dental or consequential damagers, or
limitations on how long an implied war-
ranty lasts, so the above exclusions or
limitations may not apply to you. This
warranty gives you specific legal rights
and you may also have other rights
which vary from state to state.
To obtain warranty service for a defec-
tive product, please return the product,
preferably in the original carton, along
with your purchase receipt, to the store
of original purchase for the first 90 days.
A note detailing the complaint would be
helpful. The store, at its option, will
replace or repair this product if found to
be defective.
If the unit has been purchased more
than 90 days ago, pls return it to Impact
Distribution Services, 6262 Patterson
Pass Road, Suite C, Livermore, CA 94550
together with the original receipt and
$3.95 to cover postage and handling. It
will be repaired or replaced at the manu-
facturer's option. The manufacturer
reserves the right to substitute a current-
ly manufactured model with equal or
superior features.
ADDITIONAL INFORMATION
ONE FOR ALL® is the registered trade-
mark of Universal Electronics Inc.
Computime International Ltd. is the
Licensee of the ONE FOR ALL® brand
for USA and Canada.
Copyright 2001 by Universal Electronics
Inc. No part of this publication may be
reproduced, transmitted, transcribed,
stored in any retrieval system, or trans-
lated to any language, in any form or by
any means, electronic, mechanical, mag-
netic, optical, manual, or otherwise,
without the prior written permission of
Universal Electronics Inc.
One For All® Access 3 is compatibile for
use in North America excluding Mexico.
URC-3605
10/01
Advertisement
