GE Just Cut 19250 Assembly Instructions

GE Branded Christmas Trees
with Easy Light Technology
eliminates cord connections
Assembly Instructions
Nicolas Holiday Inc. thanks you for purchasing this pre-lit Christmas
tree. Should you have any problems with your tree, visit us at
www.geholidaylighting.com
toll free number at 1-877-398-7337.
Check our website for latest service hours and assembly instruction videos.
1. Carefully unpack, removing any bubble wrap and inspect the
contents of your tree. {Fig. A}
A
A
The tree stand should be open and set at 90 angle.
Remember to tighten the thumbscrew after
connecting section A and tree stand. See {Fig. B}
Hang speaker on the bottom of the tree
as shown.
Untwist the red metal tie wrap
holding the branches in place.
Gently position any branches
that do not fall into place.
C
NOTE: No tools required
Tree Sections
7.5 ft trees 3
* Does not include time for shaping branches, estimated shaping time is 30 minutes/section.
DISCLAIMER
: DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS
LIGHTING OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB
SOCKET. DOING THIS MAY RESULT IN DAMAGE TO YOUR CHRISTMAS
TREE OR CAUSE PERSONAL INJURY. DOING THIS, WILL RESULT IN A
VOID OF THE LIMITED WARRANTY OF THIS PRODUCT.
Disconnect the decorative item from the power source before
performing any maintenance or cleaning.
For indoor use only
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
GE is a trademark of General Electric Company
and is under license by Nicolas Holiday Inc.
Distributed by Nicolas Holiday Inc.,
©2019 Nicolas Holiday Inc.,9 F., No. 37, Guangfu North Rd.
Taipei, Taiwan 10560
120V Printed in China
8.25"x11.25"
®
for more information. You can call our
B
B
2. When you connect two tree sections,
it is important that you align the mark
on the tree poles. See {Fig. C}
Approx. Asm Time *
Tree Stand
Metal 10 – 15 minutes
All rights reserved.
HG19-ONEPLUG-RGB
TREE ASSEMBLY DIAGRAM
TOP
B
TOP
A
90
3. Assemble section by section. Firmly seat both sections together.
Note: Always unplug this product before installing.
Do not plug in tree to a power outlet until the entire tree is assembled.
Thumbscrew
4. Bluetooth mode and RF (radio frequency) mode are two independent mode
features and can only be used one mode at a time.**
**See detailed function manual insert within the remote control package.
Troubleshooting Tips
If the tree does not illuminate, make certain the wall switch is turned on.
If one section of your tree does not illuminate, check that section for loose or missing bulbs,
all factory connections are properly made or that you properly made all the electrical
connections between each tree section, i.e., tree plug to extension cord outlet.
Tree Storage
1. Remove the tree's main extension cord plug from the wall outlet.
2. Starting at the top, disconnect the top and section B.
Step A: Gently fold the branches up
toward the center.
Care should be taken
to avoid damage to the lights.
3. Disconnect sections B and A.
4. Refer to the drawing on how to
repack your tree.
IMPORTANT: Store your carton neatly in a cool, dry location protected from
sunlight to prolong the tree life and to better keep the light sets in working order.
Do not place a heavy load on the carton to avoid damage to or crushing the carton
and tree inside.
SPARE PARTS: Your tree includes a plastic bag containing spare LEDs and spare
two (2) 3-amp fuses as replacements for the plug.
7.5'
AC PLUG
FOR
TREE TOP
REMOTE CONTROL
SPEAKER
A
7 colors
64 functions
8 patterns
one button, one mode
memory lock
1. Fade
2. Twinkle
3. Flash
4. Dual Color
5. Chasing
6. Steady
7. Combo
8. Music
9. Volume
7.5 FT TREES
B
TOP