QuikDrive QD PRO175G2 Operating Instructions

The Leading AutoFeed Screw Driving System - Worldwide
QD PRO175G2, QD PRO200G2, QD PRO250G2
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
WARNING - When using electric tools, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and personal injury,
including the following:
WHEN SERVICING USE ONLY IDENTICAL QUIK DRIVE
1. POLARIZED PLUG. If your screwgun has a polarized plug (one blade is wider
than the other) it will fit into a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug, if it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
2. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
3. AVOID DANGEROUS ENVIRONMENT.
power tools in damp or wet locations. Keep area well lit. Avoid chemical or cor-
rosive environment. Do not use tool in presence of flammable liquids or gases.
4. GUARD AGAINST ELECTRIC SHOCK.
For example; pipes, radiators, ranges, refrigerator enclosures.
Do not let visitors contact tool or extension cord. All
5. KEEP CHILDREN AWAY.
visitors should be kept away from work area.
6. STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or
locked-up place - out of reach of children.
7. DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was
intended.
8. USE RIGHT TOOL. Don't force a small tool or attachment to do the job of a heavy
duty tool. Use the tool for it's intended purpose only. For example; don't use a cir-
cular saw for cutting tree limbs or logs.
9. DO NOT ALTER THE TOOL Don't remove any parts from the tool.
10. DRESS PROPERLY. Do not wear loose clothing or jewelry. Loose clothing, draw
strings and jewelry can be caught in moving parts. Rubber gloves and non-skid
footwear are recommended when working outdoors. Wear protective hair cover-
ing to contain long hair.
11. USE SAFETY GLASSES. Wear safety glasses or goggles while operating power
tools. Also face or dust mask if operation creates dust.
12. DON'T ABUSE CORD. Never carry tool by cord or yank it to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges. Have damaged or worn
power cord and strain reliever replaced immediately. Do not attempt to repair
power cord.
OPERATING INSTRUCTIONS
REPLACEMENT PARTS.
®
Don't expose power tools to rain. Don't use
Prevent body contact with grounded surfaces.
13. SECURE WORK. Use clamps or a vise to hold work. It's safer than using your
hand and it frees both hands to operate tool.
14. DON'T OVERREACH. Keep proper footing and balance at all times.
15. DISCONNECT TOOLS when not in use, before servicing, and when changing
accessories.
16. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories.
Inspect tool cords periodically and if damaged, have repaired by authorized serv-
ice facility. Inspect extension cords periodically and replace if damaged.
17. REMOVE ADJUSTING KEYS AND WRENCHES.
keys and adjusting wrenches are removed from tool before turning it on.
18. AVOID UNINTENTIONAL STARTING.
sure switch is off when plugging in.
19. EXTENSION CORDS. Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.IF IN DOUBT USE NEXT HEAVIER GAUGE.
A smaller number indicates a heavier gauge.
20. OUTDOOR USE EXTENSION CORDS.
sion cords marked "Suitable for use with outdoor appliances - store indoors when
not in use.
21. STAY ALERT. Watch what you are doing. Use common sense. Do not operate
tool when you are tired.
22. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part
that is damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that is damaged should be
properly repaired or replaced by an authorized service center unless otherwise
indicated elsewhere in this instruction manual.
23. REPAIRING TOOL. Any repairs to electric tools should only be performed by
qualified personnel. To keep your Quik Drive operating most efficiently only use
original Quik Drive parts for repair.
SAVE THESE INSTRUCTIONS
Form habit of checking to see that
Do not carry a tool with finger on switch. Be
When tool is used outdoors, use only exten-