Coleman 2000002596 User Manual

ROCKWALL
Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.
Pole Descriptions
Pole
Description Qty. Dia.
Long Leg Pole, steel
(w/ red marking) 2 19mm
Short Leg Pole, steel 4 19mm
Curved Ridge Pole, steel
(w/ red marking) 1 19mm
Curved Ridge Pole, steel 2 19mm
Vertical Door Pole, black,
short w/rubber tips 1 6.3mm 5010000543
Door Pole, black,
long w/rubber tips 1 6.3mm 5010000543
Self-Rolling Window Spring Descriptions
Color Code Description Qty.
Green 1
Orange 10
CAUTION: "Springs" may have sharp edges. Handle with care to avoid
injury. Keep out of reach of children.
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the door
facing the desired direction.
Curved Ridge Poles (3)
Leg Poles,
long (2)
2. Assemble six, steel, shock-corded, Leg Poles.
(Fig. 1)
3. Push down on steel button on tapered end
and insert into end with four holes.
NOTE: Make sure steel button locks into
third hole on pole as shown. (Fig. 2)
4. Assemble three, steel, shock-corded, curved
Ridge Poles. (Fig. 1)
5. Stretch four corners of tent until taut; then
drive plastic stake web strap of each to
secure. (Fig. 3)
6. Insert Ridge Pole (with red marking) into center sleeve on top of tent
with the red trim (Fig. 4 & 6). Insert the remaining curved Ridge Poles
into the other two sleeves on top of tent.
7. Insert curved end of Leg Pole (with red marking) into the ends of the
Ridge Pole (with red dot). Insert curved end of remaining short Leg
Poles into the ends of the remaining Ridge Poles. (Fig. 5 & 6)
Fig. 4
Curved
Ridge Pole
with Red
Marking
Sleeve
with Red
Trim
12 TENT
TM
.
Pole Pole
Repair Kit Replacement Kit
N/A 5010000678
N/A 5010000680
N/A 5010000677
N/A 5010000679
5010000545
5010000545
Length Replacement Part No.
610mm 5010000627
670mm 5010000628
Fig. 1
Leg Poles,
short (4)
Button in
third hole
Fig. 2
Fig. 3
Ridge Pole with
Red Marking
Curved End of
Long Leg Pole
Sleeve
with Red
Trim
Fig. 5
MODEL 2000002596
Curved Ridge Pole in
Curved Ridge Pole
in sleeve sleeve with Red Marking
Short Leg Pole Long Leg Pole
8. Rotate all six Leg Poles upright and insert pin on each web
loop at the side locations as shown. (Fig. 7 & 7A)
9. Stretch tent to finished size:
• Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise (Fig. 8);
• Pull up on top Leg Pole section until
tent is taut;
• Twist the lower Leg Pole clockwise
until the button locks into the center
or lowest hole;
• Repeat on remaining Leg Poles.
10. Locate Frame Clips on front and back of
tent; then attach to Leg Poles as shown.
(Fig. 9)
11. Insert plastic stakes through
web straps located at bottom
of each Leg Poles; then drive
in to secure. (Fig. 10)
Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter black pole with plastic tips);
then insert through zippered vertical pole sleeve on hinged side of
door. (Fig. 11)
2. Insert end of Vertical Door Pole into bottom hinge plate, apply
pressure to form a slight bow, then insert other tip of pole into top
hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)
3. Assemble Door Pole (longer black pole with plastic cap tips); then
insert into zippered pole sleeve at top of door. (Fig. 14)
4. Insert end of Door Pole into top hinge plate, apply pressure to form
a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)
Fig. 11
Vertical Pole
Sleeve
Door Hinge
Fig. 14
Top
Top
Door
Door
Pole Pole
Hinge Hinge
Sleeve
Sleeve
(continued on other side)
Curved Ridge Pole Fig. 6
in sleeve
Door
Short Leg Pole
Front of Tent
Fig. 7
7A
Pin
Fig. 8
Upper
Leg Pole
Section
Button
Center Hole
Lower Hole
Lower
Leg Pole
Section
Fig. 9
Fig. 10
Fig. 12 Fig. 13
Fig. 15
Fig. 16