OrbiMAX 3M Speedglas 9100MP Care & Maintenance

Care & Maintenance
3M Speedglas
™
To optimise the e ective lifetime of your welding equipment and avoid the additional cost of replacement, regular
maintenance is important. Replace all damaged parts immediately to ensure correct levels of protection.
Before use
• Helmet and head harness. Inspect for cracks or any
damaged or defective parts. Replace if needed.
• Cover lenses. To provide the best possible
vision they should be clean and without scratches.
• Face seal. If the face seal is damaged there is a great
risk that contaminated air will get inside the helmet.
Verify it's in position and free from splits and tears.
• Welding lens. Ensure low battery is not flashing
and check that the sensors are clean and uncovered.
• Breathing tube. Confirm tube is not damaged or
leaking any air. To extend the life of breathing tube,
use a tube cover or a heavy-duty rubber tube.
53 20 16
57 04 95
54 05 00
52 30 00
52 30 01
19 71 50
Part No Description Part No
168502 SWEATBAND 100 & 9100 MP PK=2 171022
168505 SWEATBAND 100 & 9100 MP PK=5 171023
168550 SWEATBAND 100 & 9100 MP PK=50 171024
169014 SAFETY HELMET COVER 9100 MP/MP-LITE 197011
169015 SHROUD 9100 MP/MP-LITE 197150
171020 LENS MAGNIFYING 1.0X 9100 100 & 9000 197151
171021 LENS MAGNIFYING 1.5X 9100 100 & 9000 422000
Welding Helmet 9100MP/9100MP-Lite
™
After use
• Clean the helmet. Wipe with a moist tissue or cloth,
both inside and outside the helmet. If you suspect that the inside
of the airduct is dirty, it must be changed.
DO NOT rinse, immerse in water or clean with solvents.
• Face seal and sweatband. Remove for additional cleaning as
needed and replace if they become unhygienic.
• Cover lenses. Clean with a soft cloth and replace if any pits or
scratches occur.
• Breathing tube. Replace if damaged, deformed or leaking any air.
• Storage. Store the helmet in a dry, clean area away from direct
sunlight, high temperatures and solvents.
16 85 02
16 85 05
57 08 95
16 85 50
53 42 00
53 62 00
53 30 01
89 60 55
89 60 56
57 28 00 / 59 28 00
Description Part No
LENS MAGNIFYING 2.0X 9100 100 & 9000 500026
LENS MAGNIFYING 2.5X 9100 100 & 9000 523000
LENS MAGNIFYING 3.0X 9100 100 & 9000 523001
EARMUFFS WITH HELMET ATTACHMENT 9100 MP 526000
FLIP UP MECHANISM 9100 MP 527000
PIVOT KIT 9100 MP 527070
BATTERY LITHIUM 9100, 100 & 9000 PK=2 528025
SFI OrbiMAX
501-503 Dowling Street
Wendouree Vic 3355
T: (03) 9088 6060
E: sales@s aust.com.au
W: www.s performax.com.au
42 20 00
53 10 00
52 80 25
19 71 51
52 60 00 50 00 26
52 70 00
52 70 70
Description Part No Description
LENS WELDING 9100XXi SPEEDGLAS 531000 HOLDER BATTERY 9100
VISOR PLATE 9100 FX PK=5 532016 SIDEWINDOWS COVER PLATE 9100 FX PK=2
VISOR PLATE ANTI-FOG 9100 FX PK=5 533001 HEAD HARNESS 9100 MP
LENS COVER OUTER STD 9100 PK=10 533505 ADAPTOR ADFLO BREATHING TUBE 9100 MP AIR
COVER LENS OUTER HC 9100 PK=10 534200 FACE SEAL 9100 MP
LENS COVER OUTER HT 9100 PK=10 536200 HEAD HARNESS BACK PART 9100
LENS COVER INNER 9100XX PK=5 540500 FRONT COVER KIT 9100 FX
Further information and advice
Scan this QR-code to see
To request a quote or place an order for spare parts, please contact SFI on (03) 9088 6060. Please note that higher than normal levels of pollutants, heat and sparks
videos and learn more about
will require more frequent replacement of components. If you require additional guidance, please check the care and maintenance videos on our YouTube Channel
care and maintenance of your
(www.youtube.com/user/3MSpeedglas) or contact SFI Australia.
Speedglas welding helmet
17 10 20
17 10 21
17 10 22
17 10 23
17 10 24
53 35 05 16 90 15
570495 SHELL OUTER 9100 MP
570895 SHELL INNER 9100 MP
572800 HELMET WELDING WITH HARD HAT 9100 MP
592800 WELDING HELMET BUMP CAP 9100 MP-LITE
790101 CARRY BAG SPEEDGLAS
896055 HARD HAT 9100 MP
896056 BUMP CAP 9100 MP-LITE
197011
16 90 14
79 01 01