NATIONAL MACHINERY NC10.V2 Instructions

Thank you for purchasing this product. The crane is designed for removing engines from cars. It may be suitable for other purposes, but you
are warned that these instructions, and particularly the paragraphs referring to safety, must be consulted before considering any alternative use.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
1. SAFETY INSTRUCTIONS
Keep crane, and lifting slings, supports and beams, in good working order and condition. Follow the inspection requirements as described
!
in Section 5. Take immediate action to repair or replace damaged parts by contacting your supplier. Ensure that all accessory lifting devices
are suitably certified. If crane is damaged, immediately remove from service.
Ensure that the surface on which the crane is used is level and firm, and capable of supporting the crane and the maximum load.
!
Never use crane on tarmacadam or other soft surfaces.
!
Ensure that the crane legs and boom extension are locked in position before using the crane.
!
Keep children and unauthorised persons away from the work area.
!
Keep work area clean and tidy and free from unrelated materials, and ensure that there is adequate lighting.
!
Ensure that the load does not exceed the maximum lifting capacity of the crane. Overloading is dangerous. Where appropriate, use only the
!
lifting points recommended by the manufacturer of the item to be lifted, i.e. vehicle engine.
Before lifting the load ensure that the crane boom is in the lowest possible position, that there are no obstacles which may snag the load
!
whilst it is being lifted and that the area above the boom is clear.
To avoid injury, be fully aware of your own and other persons location in relation to the lifting and lowering of the load.
!
Keep a sound footing and balance and wear non-slip shoes.
!
Ensure that the centre of gravity always remains inside the crane base.
!
DO NOT harness the load at an angle and do not allow the load to swing during lifting.
%
DO NOT allow load to drop suddenly. Lower with care and ensure that you are aware of the condition of the surface onto which load is to be lowered.
%
DO NOT load beyond rated capacity for each specified boom position as indicated in Section 2. The capacity reduces as boom is extended.
%
DO NOT position any part of your body beneath the load and do not climb on the crane.
%
DO NOT use the crane to transport the load. The crane is a lifting device only.
%
DO NOT pull crane sideways when loaded.
%
DO NOT attempt to adjust the safety valve, as this has been set and sealed by the manufacturer.
%
DO NOT use this product to perform a task for which it is not designed.
%
DO NOT use whilst tired or under the influence of drugs, alcohol or intoxicating medication.
%
When not in use, store the crane, with the boom fully lowered, in a safe, dry, childproof, area.
!
I DANGER! WHEN FULLY LOWERING THE BOOM TAKE CARE NOT TO TRAP FINGERS BETWEEN RAM BODY AND RAM STOP.
WARNING: Failure to heed safety instructions and warnings may result in damage and/or personal injury, and will invalidate the warranty.
F
p
2. SPECIFICATIONS
Max. lift @ min. boom extension: mm . . . .1870 . . . .1930
Max. lift @ max. boom extension: mm . . .2075 . . . .2355
Height (max) of frame: mm . . . . . . . . . . . . . . . . . .160 . . . . . .190
Length (max) of frame: mm . . . . . . . . . . . . . . . . .1280 . . . . .1830
Width (max) of frame: mm . . . . . . . . . . . . . . .960 . . . .1070
Overall height (stowed): mm . . . . . . . . . . .1400 . . . .1610
Width inside frame (max): mm . . . . . . . . . .860 . . . . .920
Distance between rear wheel centres: mm . . 580 . . . . .705
3. ASSEMBLY
Note: Numbers in brackets refer to item numbers as shown in the relevant parts diagram.
3.1. Model NC10.V2
3.1.1. Fit the two legs (2 & 3) to the base (1) and retain with lock pins (4) and split pins (5).
3.1.2. Attach the post (8) to the base (1) with bolts (9) and washers and nuts (10).
3.1.3. Attach the boom (11) to the post (8) using bolt (12), washer (13) and nut (14).
3.1.4. Fit the ram (15) to the post (8) using bolt (16) and washer and nut (17) and attach the boom (11) to the top of the ram (15) using bolt (18)
and washer and nut (17).
3.1.5. Slide the boom extension (22) into the boom (11) and locate with pin (9) retained with safety clip (10), at one of the four positions.
3.1.6. Fit the hook and chain (24) to the boom extension (22) using bolt (23) and washer and nut (26).
3.1.7. Use bolts (21) and washers (20) to attach the handle (19) to the post (8).
3.2. Model NC20
3.2.1. Fit the castor wheels (24) to the base (21) using bolts (25), washers (23) and nuts (22).
3.2.2. Fit the two legs (30) to the base (21) and retain with pins (26) and lock pins (27).
3.2.3. Attach the post (14) to the base (21) with bolts (5), washers (12) and nuts (13).
3.2.4. Fit the support straps (17) between post (14) and base (21) using bolts (5) at the base and bolt (16) at the post with washers (12) and nuts (13).
3.2.5. Attach the boom (8) to the post (14) using bolt (15), washer (12) and nut (13).
3.2.6. Fit the ram (19) to the post (14) using bolt (20), washer (12) and nut (13) and attach the boom (8) to the top of the ram (19) using
bolt (11), washer (12) and nut (13).
3.2.7. Slide the boom extension (6) into the boom (8) and locate with pin (7) retained with safety clip (10), at one of the four positions.
3.2.8. Fit the hook and chain (1) to the boom extension (6) using bolt (2), washer (4) and nut (3).
NC10.V2 NC20
INSTRUCTIONS FOR:
FOLDING CRANE
N C 1 0 . V 2 & N C 2 0
Models:
Lifting capacity, position 1: kg . . . . . . . . . .1000 . . . .2000
Lifting capacity, position 2: kg . . . . . . . . . . .750 . . . .1500
Lifting capacity, position 3: kg . . . . . . . . . . .500 . . . .1000
Lifting capacity, position 4: kg . . . . . . . . . . .250 . . . . .500
Length of boom, position 1: mm . . . . . . . . .880 . . . . .970
Length of boom, position 2: mm . . . . . . . . .970 . . . .1150
Length of boom, position 3: mm . . . . . . . .1060 . . . .1330
Length of boom, position 4: mm . . . . . . . .1150 . . . .1510
NC10.V2 NC20
NC10.V2 & NC20 - 2 - 210104