Advertisement
Quick Links
INSTALLATION INSTRUCTIONS fOR OUTDOOR BI-fOLD GLASS DOORS
MODELS: 36LBfOD-BS (CAT. NO. h4645) AND 42LBfOD-BS (CAT. NO. h4646)
f i r e - p a r t s . c o m
TOOLS REqUIRED
• Medium Phillips Screwdriver
• 3/8" Open-end wrench
• 1/4" Drive socket
GENERAL INfORMATION
The door assembly consists of a right and left glass panel assembly with
the door handles factory mounted. Included is a four piece door frame
with eight (8) screws and a hood (hood packaged separately), which are
required for assembly. Fireplaces listed below on this document, have
been designed to accept these doors with minimum effort.
These bi-fold glass door assemblies have been designed for use with
and may be easily fitted to your Outdoor Gas Fireplace, Models Polaris™
36/42, VRE43 36/42, E36ODG and E42ODG.
Do not alter or modify these door assemblies or a fireplace malfunction
or a fire hazard may result.
These doors have been tested and listed by PFS Corperation.
PLEASE RETAIN ThIS MANUAL fOR fUTURE REfERENCE.
Read this instruction sheet in its entirety before beginning.
ALL WARNINGS AND PRECAUTIONS IN ThE INSTALLATION AND
OPERATION MANUAL PROVIDED WITh ThE APPLIANCE APPLY TO
ThESE INSTRUCTIONS.
ShUT DOWN ThE APPLIANCE AND ALLOW IT TO COMPLETELY COOL
BEfORE PROCEEDING.
P/N 750210M
Rev. C 04/2014
INSTALLATION PROCEDURE
Remove Screens And Rods:
Using a 5/16" socket or nutdriver, remove the screen rod assemblies (see
Figure 1). Remove the screen rod screws as shown in Figure 1. Pull out
the rods from locating holes on the side of the firebox opening.
IMPORTANT! REINSTALL SCREEN ROD SCREWS INTO ThE EXISTING
hOLES WhERE REMOVED.
The screen and rod assemblies must not be installed when the Bi-Fold
Glass Door Kit is installed. You may wish to retain the screen and rod
assemblies is case the Bi-Fold Glass Door Kit is ever removed in the future.
IMPORTANT! If ThIS OPTIONAL BI-fOLD GLASS DOOR KIT IS EVER
REMOVED, ThE ROD AND SCREENS MUST BE REINSTALLED fOR SAfE
OPERATION Of ThE APPLIANCE.
Figure 1
C
US
Report No. 14-020
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
HEARTH PRODUCTS
KITS AND ACCESSORIES
BI-fOLD GLASS DOORS
Screen Rod
Screws
Screen And
Rod Assembly
1
Advertisement
Summary of Contents for IHP 36LBFOD-BS
- Page 1 BI-fOLD GLASS DOORS Rev. C 04/2014 INSTALLATION INSTRUCTIONS fOR OUTDOOR BI-fOLD GLASS DOORS MODELS: 36LBfOD-BS (CAT. NO. h4645) AND 42LBfOD-BS (CAT. NO. h4646) INSTALLATION PROCEDURE Remove Screens And Rods: Using a 5/16" socket or nutdriver, remove the screen rod assemblies (see Figure 1).
- Page 2 After assembly, the frame inserts under the hood as shown in Figure 4 hood Installation: and drops down inside the opening without fasteners. Begin the assembly by installing the hood (packaged separately). Be certain to remove any protective plastic coatings for the stainless steel parts before installing those components.
- Page 3 IMPORTANT: ThE fINISh Of ThESE DOORS MAY BE PROTECTED WITh A SELf ADhERING PLASTIC COATING ThAT MUST BE REMOVED BEfORE hEAT IS GENERATED BY A fIRE IN ThE fIREBOX. TO PREVENT MELT- ING, ENSURE ThAT ANY PLASTIC COATING PROTECTING ThE fINISh Of ThESE DOORS IS REMOVED fOLLOWING INSTALLATION.
- Page 4 - p a r t s . c o m IHP reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information.