NINZ EXUS LA Installation, Use And Maintenance Handbook

1) Identification code:
EXUS LA PANIC EXIT DEVICE
2) Identification number: 4204301.046
3) Intended product use: Panic exit device for escape routes suitable for one-
leaved doors or for the active leaf of two-leaved
doors with dimensions up to 1350x2880mm/leaf,
mass up to 300kg/leaf, mounted on hinges or
pivots, with fire resistance up to EI
and smoke proof. Projection of the bar 125mm.
4) Manufacturer: NINZ S.p.A. - corso Trento 2/A
I-38061 ALA (TN)
tel. +39 0464 678300 - fax +39 0464 679025
5) Auth. representative: -
6) Assessment perf. sys.: system 1
7) Harmonized standard: EN 1125:2008 + EC1:2009
8) Notified body: ICIM S.p.A. N.B. no. 0425 have issued the
certificate of conformity for the factory production
control no. 0425 CPR 001228.
INSTALLATION, USE AND MAINTENANCE HANDBOOK
SYMBOLS EMPLOYED
CAUTION
Indicates a danger that threatens people and/or material goods. Failure
to observe the warnings indicated by this symbol may have serious
consequences, such as personal injury and property damage.
ATTENTION
Indicates a danger that threatens material goods. Failure to observe
the warnings indicated by this symbol may result in damage to material
goods.
NOTICE
Warnings related to important technical aspects.
PRODUCT DESCRIPTION
Panic bar for one-leaved doors or for the active leaf of two-leaved doors located
at emergency exits and activated by push-bars. Composed of galvanized
steel controls, chrome-plated polished aluminium casing and lever, horizontal
aluminium bar, stainless steel external lever handle with galvanized steel
installation plate and panic safe lock.
OPERATION MODE
From the pull-side (handle side) the door can be opened at any time whereas
from the push-side opening is always possible by using the horizontal bar of the
EXUS LA BMC panic exit device.
WARNINGS
The EXUS panic bar activated by means of a horizontal bar is intended for use
onto doors installed in escape routes where panic situations could develop.
The safety features of this product are of fundamental importance to ensure
its conformity with EN 1125. It is strictly forbidden to introduce any type of
modifications apart from those described in these installation instructions.
1/4
DECLARATION OF PERFORMANCE
No. A231-GB
KIT EXUS LA BMC
120 - REI120
2
www.ninz.it
9) Declared performances:
Essential characteristics
Category of use
Durability
Door mass
Suitability for use on fire/smoke doors
Safety toward people
Corrosion resistance
Security toward goods
Projection of horizontal bar
Type of horizontal bar operation
Field of door application
Dangerous substances
10) Panic bars listed in point 1 and 2 are conform to the performances
declared in point 9. This declaration of performance is issued under the
exclusive responsibility of the manufacturer listed in point 4.
Signed in the name and on behalf of the manufacturer:
Ninz Karl
legal representative of the NINZ S.p.A.
RECOMMENDATIONS
In order to ensure that the panic bar could provide a high level of safety toward
people and appropriate safety level toward goods, it should only be mounted
onto doors and doorframes that are in good conditions. The door itself,
therefore, should be checked to ensure that it was installed properly and that
nothing obstructs its normal movement.
If rebate sealing are mounted on the door, make sure they do not inhibit proper
functioning of the panic bar.
In case of two-leaved door where both leaves are equipped with panic
bar, it is mandatory to check that each leaf opens when its respective
panic bar is activated, and that leaves open freely when the bars are
activated simultaneously.
The fastening instructions in the present document should be followed
scrupulously during installation. Once installation is complete, the installer
should give this document to the owner of the activity.
The horizontal bar should be installed in a way that maximizes its useable
length.
For securing the door in the closed position, do not employ any other latching
devices than those specified in the present document. This does not preclude
the installation of automatic closing devices.
Different external access devices than those found on the list of certified
components on pages 4/4 are considered unacceptable.
The EXUS panic bar is also designed for installation on hollow metal doors with
an internal cell structure.
If a door closer is needed to return the door to the closed position, care should
be taken not to make the opening step more difficult for children, the elderly
and the disabled.
A pictogram (arrow) should be positioned immediately above the horizontal bar
on the internal side of the door.
All of the included components described herein must be positioned
and mounted in conformity with the present document.
Paragraph
Performance-grade EN 1125
3 - high frequency 7.1
7 - 200.000 cycles 7.2
7 - over 200kg 7.3
B - suitable 7.4
1 - for escape routes 7.5
3 - 96 h (high resist.) 7.6
2 - 1000N 7.7
1 - up to 150mm 7.8
A - push-bar 7.9
A - 1 or 2 leaved door 7.10
conform ZA
A231-GB
5001328/2 - 02/19
A231-GB