Fagron ION-e Standard User Manual

1. Performance and Main Features
The ION-e is a benchtop ionizer, compact and especially developed to meet the
daily needs of the compounding pharmacy. Its modern design allows for quick and
easy mobility, standing on the benchtop or attached to an extensor arm, enabling
the pharmacist to place it close to the operation being performed. Either to weigh,
mix or encapsulate powders, the ION-e can eliminate electrostatic charges in the
working area, preventing operational and quality issues.
2. Application
The ION-e, as the name suggests, uses ions to neutralize static electricity by
generating alternately positive or negative ions constantly, providing a fast and
e icient neutralization rate. By using the ION-e, the pharmacist can perform
pharmaceutical operations involving powders and other potencially
electrostatic materials with much more precision, preventing consequences
such as material loss during compounding, powders adherence to equipment,
lack of content uniformity, cross-contamination from equipment, and also from
the environment. With the ION-e, we bring even more quality to the compounding
process, delivering safe and e icient formulations to patients.
3. Technical Parameter
3.1 Speci ications
Model ION-e Standard, IT, GB, AU, CH
Electrical requirements 220 - 240 V
Model ION-e US, BR
Electrical requirements 100 - 120 V
Weight (Net) 1.1 kg
Dimensions 190x135x190mm (LxWxH)
3.2 Operating Conditions
Location Indoor use only
Altitude Up to 10.000 ft (3.048 m)
Ambient temperature 32ºF to 104ºF (0ºC to 40ºC)
Maximum relative humidity 10% - 90% RH @ 32ºF to 104ºF (0ºC to 40ºC)
Supply voltage luctuation Up to 24V
4. Functions and Use
1. The ION-e comes completely balanced and ready to use.
2. Place the ION-e on a lat and levelled surface, or with the optional
VESA mount adaptor on an extensor arm.
3. Position the ION-e approximately 12" (30 cm) from the area to be ionized,
with the emitter points directed preferably to the powders being handled,
and not only to the containers where they are stored.
4. Plug the ION-e in an adequate power supply.
5. Turn ON the device and proceed with compounding.
6. Turn OFF when inished.
NOTE: There are 3 LEDs located on the front panel. The one on the left
is the "Status" light (ON/OFF indicator), and the other two LEDs are
the indicators of the positive and negative. Note the rate in which
the lights switch. Your unit is set at a slow rate, balanced and ready to use.
Emitters
Status Positive/
indicator negative
ON/OFF
indicators
switch
Flat
and levelled
surface
12" (30 cm)
5. Attention
• Read the user manual carefully before operating the device.
• Only operate the ION-e with a designated AC power outlet.
• Do not operate the device with a wet or damp hand, or on wet or dump surfaces.
• Keep the e ective area of operation clear and free from obstructions of the ion low.
• Care should be in place when handling and moving the device to avoid falling face
down, as this can damage the emitter pins.
6. Maintenance
The ION-e was designed to be virtually maintenance-free. The emitter pins can be
cleaned periodically to maintain the ion low. Always check the emitter points for
dirt accumulation. When cleaning the ION-e, make sure the unit is disconnected
from power source.
6.1 Cleaning
• Always check the emitter points for dirt accumulation.
When cleaning the ION-e, make sure the unit is turned o
and disconnected from the power source.
• The outside case of the ION-e can be cleaned with a damp cloth and
normal household cleaners.
• Never submerge the device.
• To clean the emitter pins, use a swab damped in isopropyl alcohol.
6.2 Warranty
This device is under warranty and free from defects in materials and
workmanship, under normal use and service, for 24 months from the date
of invoice (excluding consumable accessories). The warranty is extended only
to the original purchaser. Warranty is not valid on a device that has been
damaged by improper installation, improper connections, misuse, accident,
or abnormal conditions of operation. If the warranty has been expired, Fagron
would still be responsible for repair with relative charges. For claims under
the warranty please contact your local supplier.