Paulson ARC-E1 SK1 PCT User Manual

User Information & User Manual
PAULSON Arc Shield Series ARC-E1
Face Shield for Arc Flash Protection
ANSI Z87.1; EN-166; EN 170; GS-ET-29
1. Introduction
This document provides all necessary information to use and maintain PAULSON Arc Shield Series
Products ARC-E1. To be properly protected you must carefully study this manual before use! Failure to
follow these instructions can result in a permanent impairment of sight or other serious personal injury.
For the Declaration of Conformity (DoC) enter the article number as shown above to the search field at
https://www.paulson-international.com.
2. General Warnings

Use by skilled persons as per your Hazard and Risk Analysis only (see Chapter 16)

Do not over expose the product to sunlight and do not use it for welding

Do not expose to open fire

Surface may get hot when exposed to electromagnetic radiation
 Only use as a kit

Only use original replacement parts

Make sure that your work place is sufficiently illuminated

Free head movement and personal view may be affected
Insufficient packing may decrease the level of protection. Thus, follow the instructions as per Chapter 9.
The following warnings are standard warnings as per EN 166:

Material which may come into contact with the wearer's skin could cause allergic reactions to
susceptible individuals. (REMARK: PAULSON carefully selects the materials and is not aware of
reported allergic reaction.)

The PAULSON Arc Shield protects against high speed particles. When worn over standard
ophthalmic spectacles, they may transmit impacts, thus creating a hazard to the wearer.
3. Field of Application
The PAULSON Arc Shield, together with additional PPE appropriate for the determined level of
protection, protects the qualified user during live electrical work / live working or when staying in the
vicinity of live electrical parts. The PAULSON Arc Shield provides safety to eyes and face only, if used as
intended. They are not intended for electric arc welding and shall not be used and or stored close to arc
welding work. They are also not intended to be used for protection against laser radiation.
©
Paulson Manufacturing Corporation 2021 Errors and technical changes reserved
Product Code Part Number
ARC-E1 SK1 PCT 2189000
ARC-E1 SK2 2189001
ARC-E1 SK4 2189002
ARC-E1 SK7 2189003
ARC-E1 S2K5C 2189004
ARC-E1 S2K5H 2189005
For permitted spare parts please go to:
https://www.paulson-international.com/products/arc-
flash-ppe/european-class-1-arc-shields/
Page 1 of 5
4. Description
The PAULSON Arc Shield kits ARC-E1 consist of a face shield with a bracket for slotted caps (Kit 1) or a
face shield with a cap bracket for slotted and un-slotted caps (Kit 2), or a face shield with a head gear (Kit
3 and Kit 4) or a face shield with attached chin protector and a head gear (Kit 5 and Kit 6).
The PAULSON Arc Shield only provides protection for eyes and face against the thermal and mechanical
hazards of an arc flash when completely assembled with all components and worn together with
additional PPE appropriate to the determined level of protection.
5. Assembly Instructions
General:
Mount the PAULSON Arc Shield of Kit 1 and Kit 2 only to a helmet that is approved for arc flash protection
at the maximum expected level. In case of any doubt, contact your helmet manufacturer. Tighten the pivot
screws, so that the Arc Shield easily can be raised or lowered and securely rests in any position.
Installation for Kit 1 (Slotted Caps)
Insert the black adapters (snap-in blades) of the PAULSON Arc Shield cap bracket into the accessory
slots at the sides of the helmet. There will be an audible click when the black adapter is fully seated into
the slot of the helmet.
Installation for Kit 2 (Slotted or Un-slotted Caps)
Center the PAULSON Arc Shield on the front of the helmet placing the front brim into the groove of the
cap bracket; pull the elastomeric band over the top of the shell. Assure cap bracket is centered and has
captured the helmet brim for a secure fit.
Installation for Kit 3 and Kit 4 (Visor combined with Headgear without chin protector)
Release the headband by turning the ratchet wheel at the back of the headgear. Put the headgear on
your head and center it. Shorten or expand the upper band to adjust it to the best fitting wearing height.
Tighten the ratchet to fit it to your head size. Please note, that the head circumference changes in the
course of the day, readjust the headband accordingly.
Installation for Kit 5 and Kit 6 (Visor combined with Headgear with chin protector)
Release the headband by turning the ratchet wheel at the back of the headgear. Put the headgear on
your head and center it. Shorten or expand the upper band to adjust it to the best fitting wearing height.
Tighten the ratchet to fit it to your head size. Please note, that the head circumference changes in the
course of the day, readjust the headband accordingly. Make sure that the chin protector is securely
fastened to the visor. NOTE: Kit 5 and Kit 6 can provide the intended protection only, when the visor is
used together with the chin protector.
6. Fitting Instructions for Arc Shield Assembly
Position the helmet or the headgear with the PAULSON Arc Shield on the head and pull the Arc Shield in
the deployed, vertical position.
7. Usage
7.1. General
Always check the PAULSON Arc Shield assembly components before use. Make sure the PAULSON Arc
Shield is securely fastened to the cap bracket or headgear with the cam locks. Adjust the bracket to the
cap, if necessary. With the kits 5 and 6 also check the connection between the chin protector and the
visor (by the cam locks).
NOTE: A headgear never can fully substitute a safety helmet. Due to national safety rules and company
policies in some countries or companies, the usage of a helmet is mandatory. For the same reason safety
glasses may need to be worn underneath the visor.
NOTE: An arc flash / electrical fault arc of high incident energies may cause permanent impairment of
sight or other serious personal injury. PPE - Personal Protective Equipment should be considered as the
last barrier if everything else fails. Consider higher protective equipment to gain extra safety buffers in
case an accident generates more energy than originality calculated in the hazard and risk assessment.
However, there should be no live working under conditions, which cannot be protected by Arc Protection
©
Paulson Manufacturing Corporation 2021 Errors and technical changes reserved Page 2 of 5