Download Print this page
Vision ZL 7261 CL-5 Operation Manual

Vision ZL 7261 CL-5 Operation Manual

Advertisement

Quick Links

Federal Communications Commission Statement
This equipment has been followed to comply with Part 15 of the FCC Rules. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try and correct the
interference by one of the following measures:
-Reorient or relocate the receiving antenna,
-Increase the separation between the equipment and receiver,
-Connect the equipment into and outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesirable operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
Limited Warranty
Vision Guarantees that every wireless lighting module is free from physical defects
in material and workmanship under normal use for one year from the date of
purchase. If the product proves defective during this one-year warranty period,
Vision will replace it free of charge. Vision does not issue any refunds. This warranty
is extended to the original end user purchase only and is not transferable. This
warranty does not apply to: (1) damage to units caused by accident, dropping or
abuse in handling, or any negligent use; (2) units which have been subject to
unauthorized repair, taken apart, or otherwise modified; (3) units not used in
accordance with instruction; (4) damages exceeding the cost of the product; (5)
transit damage, initial installation costs, removal cost, or reinstallation cost.
For information on addional devices, plesae visit us at www.visionsecurity.com.tw
-5-
ZL 7261/7201
V5
1050902
6B1Z-72003
Operation Manual
ZL 7261 CL-5
ZL 7261 CN-5
ZL 7261 DE-5
ZL 7261 FR-5
ZL 7261 IT-5
ZL 7261 JP-5
ZL 7261 KR-5
ZL 7261 RU-5
ZL 7261 US-5
Z-Wave Power Monitor
ZL 7201 CL-5
ZL 7201 CN-5
ZL 7201 DE-5
ZL 7201 FR-5
ZL 7201 IT-5
ZL 7201 JP-5
ZL 7201 KR-5
ZL 7201 RU-5
ZL 7201 US-5
Z-Wave On/Off Module

Advertisement

loading

Summary of Contents for Vision ZL 7261 CL-5

  • Page 1 If the product proves defective during this one-year warranty period, ZL 7261 US-5 Vision will replace it free of charge. Vision does not issue any refunds. This warranty Z-Wave Power Monitor is extended to the original end user purchase only and is not transferable. This...
  • Page 2 Introduction Protocol: Z-Wave (ZM5202) Power Monitor or On/Off Module Thanks for choosing the Vision’s Power Monitor or On/Off Module of the home automation device. This Frequency: 1pc User Manual Power Monitor or On/Off Module is a Z-Wave enabled device (interoperable, two-way RF mesh 868.42 MHz (ZL7201CN/DE/FR/IT / ZL7261CN/DE/FR/IT)
  • Page 3 For “Meter Supported Get” (ZL7261 only): the Z-Wave Interface Controller or Gateway can send “Meter Get” command with any of the following supported scales, and the 10. Protection function (ZL7201 only) ZL7261 will report back with the energy consumption values for the requested scale: Protection State Program Switch Notes...

This manual is also suitable for:

Zl 7261 cn-5Zl 7261 de-5Zl 7261 fr-5Zl 7261 it-5Zl 7261 jp-5Zl 7261 kr-5 ... Show all