Quoizel SNNL8411PN Installation Manual

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: LED 22W
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact your original place of purchase.
Fixture can only be mounted in the direction indicated .
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Package Contents
Crossbar
A Assembly
x 1
Outlet Box Screw
C
x 2
Alternate
Mounting
E
Screw
Wire Connector
D
x 2
x 3
-
STEP 1 Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(C). Tighten until snug.
Outlet
Box
Figure 1
-
STEP 2 Fit Backplate to
Crossbar Assembly
A. Remove mounting balls from the
Crossbar Assembly (A). Fit the
backplate on Fixture Body (B) to
the Crossbar Assembly (A) and
secure with mounting balls.
Note: The backplate on Fixture
Body (B) should be snug against
the wall and the mounting balls.
If not, adjust the length of the
mounting screw on the Crossbar
Assembly (A) by unscrewing the
preassembled hex nut and lock
washer and then screwing the
mounting screws in or out of the
crossbar until the correct length
is achieved. Once the backplate
on Fixture Body (B) is secure,
remove the mounting ball and
Fixture Body (B) and proceed to
Step 3.
2018 QuoizelInc.
For Styles SNNL8411K and SNNL8411PN
for product cleaning tips. Go to the
20-30 minutes
Fixture Body
B
x 1
A
C
Supply Wires
with Ground Wire
Backplate
Mounting
Mounting Ball
Screw
A
Hex Nut and
Lock Washer
Figure 2
visit us on-line at www.quoizel.com
Installation Guide #IS-SNNL8411
Care + Maintenance selection.
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (D) to make all wire connections.
Twist connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
-
STEP 4 Install Fixture Body
A. Position the backplate and
Fixture Body (B) onto the
Crossbar Assembly (A).
Place the holes in the
backplate over the mounting
screws. Secure the Fixture
Body by using the mounting
balls and hand tighten the
mounting balls until snug.
STEP 5 - Apply Silicone Sealer
B
A. Make sure exterior wall surface and
fixture backplate are free of dirt
before applying caulk. Using
exterior grade caulk, caulk over top
of backplate and down other side.
Do not caulk bottom of fixture
backplate to ensure proper moisture
drainage.
Your fixture is now assembled and
ready to use. Enjoy!
1of2
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Green Ground Screw
on the Crossbar
A
Mounting Screw
Figure 4
ReleasedDate:2019-08-09
Figure 3
Backplate
Mounting Ball
B
Exterior
Grade
Caulk
Backplate
Figure 5