J&J Electronics PureWhite LPL-P2-WHT-12-S Installation And Operation Manual

TM
PureWhite 2 Pool & Spa Lamp Installation and Operation Guide
PUREWHITE REPLACEMENT LED IN-GROUND POOL & SPA LAMPS
Model #s: LPL-P2-WHT-12-S, LPL-P2-WHT-120-S, LPL-P2-WHT-12-SQ-S, LPL-P2-WHT-120-SQ-S, LPL-M1-WHT-12, LPL-M1-WHT-120
PureWhite Replacement LED In-Ground Pool and Spa lamps offer superior, bright white illumination for your pool or spa. This owner's manual contains
important information on installing and using your new PureWhite Replacement LED In-Ground Pool or Spa lamp. Please read it carefully and keep it in a safe
place for future reference.
WARNING! This device is not intended for use with
emergency exit fixtures or emergency exit lights.
WARNING! Permanent damage to the low voltage
14VAC lamp will occur if installed on a
120VAC circuit.
PureWhite Replacement LED In-Ground Pool and Spa lamps are available in 14VAC
(low voltage) and 120VAC models as indicated on the product packaging. Each lamp
has a screw-in Edison base.
WARNING! Remove warning label from
PureWhite lens before installation.
[Does not apply to model #s: LPL-M1-WHT-12 and LPL-M1-WHT-120]
The warning label is placed on top of a special optical diffuser designed to maximize
the light projection of the PureWhite lamp. When you remove the label, a protective film
will come off with it. Once the warning label and protective film have been removed,
do not allow the diffuser decal underneath to be scratched.
ATTENTION 14V PUREWHITE OWNERS!
A socket voltage range of 13.5 – 15.0 will achieve optimal brightness. To verify the
voltage, at the lamp socket, measure the open circuit voltage (no lamp in the socket).
Set the transformer tap to 14.0VAC.
DANGER!
Risk of electrical shock or electrocution
Always disconnect power to the pool or spa light at the circuit breaker panel before
attempting to service the lamp. Failure to do so could result in serious injury or death
due to electrical shock. Refer to the original manufacturer's light installation manual
before proceeding. As with any electrical device, installation and service should
always be performed by a qualified individual. This device is not intended for use in
anything other than in-ground pools or spas.
Rated Lamp Life
The illumination generated by the PureWhite Replacement LED In-Ground Pool or Spa
lamp is based on Light Emitting Diode (LED) technology. The average expected lamp
life is rated up to 25,000 elapsed time hours under normal operating conditions.
[Temperature: 33°F to 104°F (1°C to 40°C), Humidity: 0-95% non-condensing].
Safety Precautions
•
Do not open, service or tamper with any internal component of the PureWhite
Replacement LED In-Ground Pool or Spa lamp. Doing so will void the warranty.
Follow each instruction in this owner's manual and pay careful attention to all
warnings.
•
Do not directly expose or immerse the PureWhite Replacement LED In-Ground
Pool or Spa lamp in water without containing it in a proper, watertight, NRTL
(nationally recognized testing laboratory) light housing and niche assembly.
•
Keep the light housing dry.
•
Handle the PureWhite Replacement LED In-Ground lamp with care. Be careful
not to drop the unit.
IMPORTANT NOTE:
PureWhite lamps are recommended for installation by a qualified pool or spa professional.
Installation
The installation steps in this owner's manual are intended as guidelines. For specific
instructions on how to replace a pool or spa lamp, please refer to the original
manufacturer's light installation manual before proceeding.
Light housing compatibility
LPL-P2-WHT-12-S, LPL-P2-WHT-120-S, LPL-P2-WHT-12-SQ-S,
LPL-P2-WHT-120-SQ-S, LPL-M1-WHT-12, LPL-M1-WHT-120
PureWhite Replacement LED In-Ground Pool and Spa lamps must be installed in a
compatible NRTL light housing.
•
J&J Electronics 6 Bendix, Irvine, CA 92618 USA
Compatible NRTL light housings include:
®
Hayward Astrolite SP058 Series
™
Pentair ® Amerlite 784 Series
Jacuzzi ® Full Moon
™
®
Sta-Rite SwimQuip Series 0508
™
Hayward ® Astrolite II SP059 Series
™
Pentair ® SpaBrite Series
™
Gasket compatibility
®
Hayward Astrolite ™ SP058 Series Housing - Use
replacement gasket specified by manufacturer.
®
Pentair Amerlite 784 Series - Requires installation of J&J Gasket #LPL-G-P.
Included with LPL-P2-WHT-12-S and LPL-P2-WHT-120-S.
®
Jacuzzi Full Moon ™ - Use replacement gasket specified by manufacturer.
®
™ Series 0508 - Requires installation of J&J Gasket #LPL-G-S.
Sta-Rite SwimQuip
Included with LPL-P2-WHT-12-SQ-S and LPL-P2-WHT-120-SQ-S.
®
Hayward Astrolite ™ II SP059 Series - Use replacement gasket specified by manufacturer.
®
Pentair SpaBrite ™ Series - Requires installation of J&J Gasket #LPL-M-G-P.
Included with LPL-M1-WHT-12 AND LPL-M1-WHT-120.
The product warranty is voided if the proper gasket is not installed.
See the "Warranty" section at the end of this manual for details.
WARNING!
Read this before attempting installation
Your PureWhite lamp is not an ordinary light bulb. It is a valuable electronic device that
is not designed to come in direct contact with water. An improper installation that
results in water leakage into the light housing can permanently damage the PureWhite
lamp. Please read these installation steps and the original manufacturer's light
installation manual carefully before proceeding.
STEP 1
Remove light housing from niche
Make sure power to the pool or spa light is turned off at the circuit breaker. Carefully
remove the existing light housing from the niche assembly and place it on the deck.
There should be enough power cord to do this easily. If there is not enough power cord
to allow the light housing to reach the deck surface, call your local pool or spa service
company.
WARNING! Verify that your PureWhite lamp voltage rating (120VAC
or 14VAC) matches your electrical system's voltage requirements
before proceeding with installation.
STEP 2
Remove old lamp
Access the old lamp according to the original manufacturer's light installation manual.
Remove the screws and/or loosen the clamp that holds the face plate and lens in
place. Carefully remove the lens from the light housing. Take care not to damage the
surface of the light housing body that makes contact with the rubber gasket.
• •
800.735.4553 949.455.4460
Figure 1: LPL-P2-WHT
Figure 2: Step 1
•
www.jandjpoolspa.com
PAGE 1