UltraPro 44127 Manual

44127 (10IN.), 44128 (16IN.)
PLUG-IN
LED LIGHT FIXTURE
SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO YOUR
CABINET SO YOU CAN REFER TO THEM AT A LATER TIME.
CAUTION: DO NOT OVER TIGHTEN SCREWS
DO NOT USE WITH A DIMMING CIRCUIT OR ANY OTHER
ELECTRONICALLY SWITCHED CONTROL.
IMPORTANT SAFETY INSTRUCTIONS
The LED light fixture has a polarized plug (one blade is wider than the other) as a feature
to reduce the risk of electric shock. This plug fits in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Never use with an extension cord unless plug can be fully inserted.
Do not alter the plug. Read entire installation procedure before you begin.
INSTALLATION PROCEDURE FOR PLUG-IN LED LIGHT FIXTURE
Carefully plan out your installation prior to actually securing your LED light fixture to the
mounting surface making sure that your 5ft. line cord will reach the nearest electrical
outlet. For kitchen installations, the recommended mounting for the LED light fixture is
near the front lip of your kitchen under cabinets as shown in the illustration Figure 1. This
provides the best light distribution across a countertop.
1. DO NOT ATTEMPT TO INSTALL LED LIGHT
FIXTURE WHILE PLUGGED IN.
2. Select a suitable dry mounting location (for use
indoors only). Make sure mounting surface is
capable of supporting the LED light fixture.
3. Hold the LED light fixture in desired location and
clearly mark the locations for the mounting holes.
4. Using a 3/32in. drill bit, pre-drill holes into the
mounting surface. Mounting is via keyholes; when
inserting the provided screws, leave 1/8in. of the
screw heads protruding beyond the mounting
surface.
5. Mount the LED light fixture to surface by aligning
screws to keyholes and sliding into place to
secure, as shown in Figures 2 and 3. If necessary,
tigthen screws to secure in place.
6. Plug the LED light fixture into a 120VAC 60Hz
outlet.
CLEANING INSTRUCTIONS
Your LED light fixture is made from quality materials that will
last for many years with minimum care. When cleaning, make
sure you have unplugged your LED light fixture and have
allowed a sufficient amount of time for it to cool to room
temperature. You should clean the housing and lens using
a soft, damp cloth. Do not use chemicals to clean your LED
light fixture, as this could damage or discolor your LED light
fixture. You should plug your LED light fixture back in only
after it has thoroughly dried.
READ IT OR WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit bit.ly/2KGwKxc
FIGURE 1
CABINET
COUNTER TOP
FIGURE 2
CABINET
FIGURE 3
INSERT
SLIDE
FCC/IC - EN
Suppliers Declaration of Conformity | Model #: 44127 | 44128 | Jasco Products Co., 10
E. Memorial Rd, Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interfer- ence, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interfer- ence in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communica- tions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
SPECIFICATIONS
44127 (10IN.) 44128 (16IN.)
120VAC 60Hz 120VAC 60Hz
4.95W 5.85W
340 Lumens 445 Lumens
81 CRI 81 CRI
2700K CCT White 2700K CCT White
WARNING
RISK OF ELECTRICAL SHOCK
• DO NOT USE IN WET LOCATIONS
• USE INDOORS ONLY
• USE ONLY INSULATED STAPLES
OR PLASTIC TIES TO SECURE THE
CORDS
• ROUTE AND SECURE THE CORDS SO
THAT THEY WILL NOT BE PINCHED
OR DAMAGED
NO SERVICEABLE PARTS
NON-REPLACEABLE LEDS
LED LIGHT OUTPUT IS STRONG
ENOUGH TO INJURE HUMAN EYES.
PRECAUTIONS MUST BE TAKEN TO
PREVENT LOOKING DIRECTLY AT THE
LEDS WITH UNAIDED EYES FOR
MORE THAN A FEW SECONDS.
RISK OF FIRE
• NOT INTENDED FOR ILLUMINATION
OF AQUARIUMS
• NOT INTENDED FOR USE ABOVE
STOVES, COOK TOPS, SINKS
OR OTHER HEAT PRODUCING
APPLIANCES, SUCH AS COFFEE
MAKERS, TOASTERS, OR TOASTER
OVENS
MADE IN CHINA/HECHO EN CHINA
Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a limited-lifetime warranty. Visit www.byjasco.com for
warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between
7AM—8PM M-F, Central Time.
©JASCO 2020 | 44127, 44128 | 05/12/20 v3
• NOT INTENDED FOR RECESSED
INSTALLATION IN CEILINGS OR
SOFFITS
• NOT INTENDED FOR SURFACE
INSTALLATION INSIDE OR ON TOP
OF BUILT-IN FURNISHINGS SUCH
AS KITCHEN CABINETS, CHINA
CABINETS, OR TROPHY CASES
• DO NOT CONCEAL POWER SUPPLY
CORD OR LINKING CORDS INSIDE
A WALL, CEILING, SOFFIT, KITCHEN
CABINET, OR SIMILAR PERMANENT
STRUCTURE
• DO NOT RUN THE POWER SUPPLY
CORD OR LINKING CORDS
THROUGH HOLES IN WALLS,
CEILINGS OR FLOORS