OneKing H Series Instruction Manual

Video Conference Camera with Expansion Microphone(s)
Controls and Functions
< Front View >
Functions LEDs indicator
The indicator lights up when using the device.
Lens Camera Scroll wheel
( 4K/2K optional )
Adjust ±15 degrees of the lens
go up and down.
< Rear View >
H Series
For LAN
DC IN 12V Power supply interface
For connecting USB3.0 Cable
M/L Series
DC IN 12V Power supply interface
For connecting USB2.0 Cable
< Top View >
Functions of the buttons on the top
1 Connection indicator
2 Microphone mute 3 Speakerphone m m u u t t e e
Power on/off
4 Volume down 5 Volume up 6
Buttons Indicator status Functions
Orange LED lights Connected to PC successfully via USB
1 Connection indicator
Blue LED flashes
Disconnected
2 Microphone mute All the mics mute
Orange LED lights
3 Speakerphone mute Orange LED lights Speakerphone mute
4
Volume down Volume down
Blue LEDs decrease
progressively
Blue LEDs increase
5 Volume up
Volume up
progressively
Press 3 seconds to power on
Blue LED lights
Power on/off
6
Blue LED off Press 3 seconds to power off
< Wireless Expansion Microphones.Top View(left), bottom View(right) >
Power on/off
2
1 Mute Microphone 3 Copper ring
Buttons Functions
1 Mute Microphone
Microphone mute
Power on/off
Press 3 seconds to power on/off
2
When using the charging tray, the charging
3 Copper ring copper ring acts as the charging interface.Charging
copper ring contacts spring probe for charging
Red LED flashes
Low battery
Charging time Standby time
Battery Working time
Notes-Tips
1) High-end, mid-end and low-end configuration optional, support standard UVC
protocol.
H Series M Series L Series
2) The audio output of this device use the same USB interface with video and
supports the standard UAC protocol. All the software which supports the UAC
protocol can collect the audio of this device.
3) Daisy-chain max up to 3 wireless expansion microphones connect to main unit
via RF2.4G transmission. Each expansion microphone provides 3 meters pick up
range. To ensure the call quality and echo cancellation effect, please do not move
the expansion microphone after placing it on the table. At the same time,
expansion microphones need a distance at least 1 meter from the speaker.
4) The main unit has an internal auxiliary microphone for emergency use when
the expansion mics are out of power. Expansion mics are recommended for the
best call experience. When any expansion mic is turned on, the internal mic will
be automatically disabled.
Combination Key Function
2) Prompt tone ON/OFF
Prompt tone is turned on by default. Press and hold for 5 seconds to
turn ON/OFF.
3) Enable or disable the internal microphone
Press and hold for 5 seconds to enable or disable the internal mic
4) Remote upgrade mode
(This function needs the support of the manufacturer, please do not use it
under normal circumstances)
Press and hold for 5 seconds to enter remote upgrade mode, only the
orange indicator of Power button lights.
Press and hold for 5 seconds to exit the upgrade mode.
Pairing Wireless Microphones
microphone close to the main unit.
paired.
Music Mode
main unit
What is content in package ?
①Video conference camera * 1 ⑥ USB 3.0 cable 3M (H Series) * 1
USB 2.0 cable 5M (M/L Series) * 1
②User's manual * 1
⑦Power supply of the camera * 1
③Expansion mics * 1-3
⑧Power supply of the charging tray * 1-2
④Charging tray * 1-2
⑨USB - type C cable * 1-2
⑤Bracket and screws * 1
⑩Remote control (no battery) * 1
Remote control's functions
Buttons Functions
1
Power on/off Power on/off
3 1
2
2 Zoom out Camera zoom out
4
3 Zoom in Camera zoom in
6 5
Camera functions' Camera functions' menu (center)
4
7
menu EPTZ control (up, down, left, right)
5 Microphone mute Microphone mute
6 Speakerphone mute Speakerphone mute
7 Volume up/down "+" volume up; "-" volume down
Note: If the remote control is not available, maybe the batteries ran out. Please
change the new batteries(AAA*2pcs) .
Auto-Framing(H Series Only)
H Series support Auto-Framing camera control, automatically moves the lens and
adjusts the zoom to comfortably frame meeting participants in rooms of all
shapes and sizes.
❶
Press "Camera functions menu"
(center), select " Setup"
❷
Select " AI Function" to "ON",
Auto-Framing function turns on.
AI "Refresh Freq" is adjustable
"Low/Mid/High".
Picture in Picture(PIP) (L Series Only)
L Series support Picture in Picture(PIP) function, while EPTZ zooms in close-up,
users can view the panorama through the small picture-in-picture window.
❶
Press "Camera functions
menu"(center), select "Image"
❷
Select "PIP" to "On" , Picture in
Picture function turns on, users
can see small picture-in-picture
window at the bottom of right.
Installation instruction
Desktop installation
1
Put the device on the table or
screen and make sure the
horizontal installation.
Horizontal placement
2 Bracket installation
Screw the bracket to the screw hole at the bottom of the device and tighten it.
Then the user can install a bracket at the bottom of the device. The screws of
the bracket must meet the following specifications.
φ=3mm
L=6mm
Screw specification
Note:
① The bracket must be installed on the flat surface.
②
The screws on the bracket of the video conference camera can't be used
on the higher place, just like the ceiling mount or partition mount.
3 Wall mount
❶Install the bracket at the bottom of the camera according to
the 2 Bracket installation .
❷Screw the bracket on the wall, refer to the following picture 1.
❸Fasten the camera with bottom bracket on the wall mount, refer to the
following picture 2.
(Picture 1) (Picture 2)
Note:
③ The wall mounted bracket must be flat
④
The wall bracket is used in conjunction with the bracket. The device must
install the bracket
Connect to the computer
❶
Connect the 12V power supply to the camera.
Connect the standard USB cable with the camera and computer or other host
computer. Refer to the following picture:
LAN(H Series only)
DC 12V power supply
USB 3.0/2.0 cable
Video instruction
This device output video through USB. And it supports standard UVC protocol. All
the software which support the UVC protocol can collect the video of this device.
1) Demonstrate the video usage of the device with common software AMCAP.
❶ Open the AMCAP (available in
the CD) and click the Devices.
4K UCamera
Then choose the 4K UCamera
麦克风（17-USB Audio Device）
(or the similar option)
❷
Click the Options and
choose Preview. Then the
user can preview the video.
Refer to
the right picture.
2) If the frame rate is not enough, the user can check whether the " Use Frame
Rate" is ticked off. If yes, please cancel the tick
❶
Click the Capture and then
choose Set Frame Rate
❷
In Choose Frame Rate, check
whether the "Use Frame Rate"
is ticked off. If yes, please
cancel the tick. And then click
the Apply
Cancel the tick in the frame
3) Change the different resolution and frame.
❶
Click the Options and choose
Video Capture Pin...,
❷ Set the different resolution
and frame according the
user's requirement. And
then click Apply
Click Apply
How is working in meeting rooms ?
1 microphone 2 microphones
3 microphones