Advertisement
Quick Links
Kahlenberg
KAHLENBERG P449 SERIES COMPRESSORS
PART NOS. P449-17, P449-18, Compressor Kits
WITH P569-01A and P569-02A Compressor Pump Assemblies
REFERENCES:
Thank you for buying a Kahlenberg P449 Series Intermittent Duty Compressor Kit. This
is an automatic, powerful, and compact accessory for your air horn system and should
give you years of trouble-free performance. Although installation of this compressor kit
is straightforward and simple, we offer the following guidelines to assist you.
THIS COMPRESSOR SYSTEM IS RATED FOR INTERMITTENT DUTY ONLY.
PLEASE READ AND UNDERSTAND THESE INSTRUCTIONS INCLUDING
SAFETY PRECAUTIONS ON PAGE 5.
IMPROPER INSTALLATION CAN BE DANGEROUS, AND MAY ALSO
RESULT IN PERMANENT DAMAGE TO THE SYSTEM WHICH IS NOT
COVERED UNDER WARRANTY.
THE FOLLOWING ITEMS ARE INCLUDED IN THIS PACKAGE:
(1) P449 Series Compressor Pump Assembly including air gauge, safety
valve and 1/4" tube fitting installed
1. Arrange compressor, tank, and air horn in such a way as to keep air line runs as
short as possible. It is best to mount the valve (whether electric or manually
operated) directly to horn with 1/8" N.P.T. nipple, provided. See additional valve
instructions enclosed if you have purchased a Kahlenberg valve. The kit provides
you with 8' of ¼" SAE J844 brake line tube (for installation between pump and
tank) and 15' of 5/16" tube (for installation between tank and horn operating
valve). Some custom O.E.M. kits provide longer lengths of tubing. Lengths up to
50' between the tank and valve may be used and can be purchased from
Kahlenberg or your local industrial supply store. Use ONLY ¼" SAE J844 tube
or equivalent between compressor and tank. Use connectors already installed on
compressor and tank. Cut tube off square with razor or sharp knife and push
firmly into connector. To disconnect, press in on red connector collar and pull
tube out. This provides a simple, airtight flexible connection. See Installation
Drawings 3-6331 attached for additional details.
Instructions, P449 Series, P569-01A, P569-02A
INSTRUCTIONS FOR INSTALLING
Drawing No. 3-6331
Drawing No. 3-6577
WARNING
03/23/2010
Page 1 of 5
Advertisement
Related Manuals for Kahlenberg P449 Series
Summary of Contents for Kahlenberg P449 Series
- Page 1 Drawing No. 3-6331 Drawing No. 3-6577 Thank you for buying a Kahlenberg P449 Series Intermittent Duty Compressor Kit. This is an automatic, powerful, and compact accessory for your air horn system and should give you years of trouble-free performance. Although installation of this compressor kit is straightforward and simple, we offer the following guidelines to assist you.
- Page 2 7. If you are installing a Kahlenberg V69-K solenoid valve kit, refer to instruction sheet #306 for further guidance. (Shipped with valve kit) Page 2 of 5...
- Page 3 Kahlenberg Instructions, P449 Series, P569-01A, P569-02A 03/23/2010 IMPORTANT!!! RUN DISTANCE WIRE GUAGE Less than 10’ 14 AWG 10’ to 35’ 12 AWG 35 to 50’ 10 AWG 50 to 70’ 8 AWG NOTE: THESE ARE THE WIRE GUAGES NECESSARY FOR THE ENTIRE WIRING RUN TO YOUR POWER SOURCE (BATTERY).
-
Page 4: Troubleshooting
Kahlenberg Instructions, P449 Series, P569-01A, P569-02A 03/23/2010 TROUBLESHOOTING IF THE COMPRESSOR DOES NOT SHUT OFF AFTER APPROXIMATELY 5 MINUTES OR IF IT SHUTS OFF BUT INTERMITTENTLY TRIES TO START UP (CHUGS), IMMEDIATELY DISCONNECT POWER AND CHECK THE FOLLOWING: • VERIFY THE CURRENT AND WIRE SIZE (SEE ABOVE SUGGESTED WIRE SIZES) GOING TO THE COMPRESSOR. -
Page 5: Important Safety Information
Kahlenberg Instructions, P449 Series, P569-01A, P569-02A 03/23/2010 IMPORTANT SAFETY INFORMATION Read and understand the following information and instructions included with this product before using. This information is for your safety and to prevent damage to the product. ! CAUTION: To reduce risk of electric shock or electrocution: Do not disassemble compressor pump.