Ozeri 4X3RAZOR Manual

Tri-Axis (3D Motion) Pedometer
Product Overview
Front View
Back View
PD4X3-2
Calories:
Speed: 0 ~ 999 mph/kph
Number of steps: previous 30 days
Distance: previous 30 days
previous 30 days
Calories:
Weight: 45~350 lbs
20~160 kg
Stride Length: 1~6 feet
30~180 cm
If no activity is detected for 3 minutes, the LCD will
Auto Sleep
automatically turn off to conserve the battery. The
Mode
pedometer will still count activity in Sleep Mode. To turn the
LCD back on, press any button for 1 second.
Step Counting
Precision:
*The images in this manual are for illustration purposes only and may vary
slightly from actual product.
Getting Started
Before using your 3D Pedometer for the first time (or after changing the
battery), you will need to set it up so that it is personalized to you by
following the instructions below.
1. Remove battery tab from the pedometer by pulling the tab outwards. This
will automatically begin the setup process with the TIME screen.
2. Program each screen using the Mode and Reset buttons to increase and
decrease the digits respectively. Use the Set button to confirm each entry.
3. If a button is not pressed within 60 seconds, the pedometer will exit Setup
Mode and the screen will turn off. If this happens, apply a pin to the hole
on the back of the pedometer to perform a System Reset.
Programming your Pedometer:
1. TIME: Press MODE to switch from 24 HR and 12 HR clock display.
Press SET to confirm entry. Continue to program HOUR and MIN as follows.
PD4X3-2
Press MODE to advance by 1. For rapid advance, press and hold
MODE for over 2 seconds.
Press RESET to decrease by 1. For decrease rapidly, press and hold
RESET for over 2 seconds.
Press SET to confirm the TIME.
2. USA (Imperial) or International (Metric) Symbols: Press MODE to switch
from Imperial to Metric units of measurement.
NOTE: Changing the unit of measurement will reset the pedometer's
programming and delete all recorded exercise data.
3. STRIDE: After programming the CLOCK, the screen will flash the
default STRIDE length
(default value is 70 cm. Range is 30 to 180 cm)
Press MODE to advance by 0.25 feet (or 1 cm).
Press RESET to decrease by 0.25 feet (or 1 cm).
To advance or decrease rapidly, press and hold MODE or RESET
respectively for over 2 seconds. Press SET to confirm your STRIDE.
4. WEIGHT: After programming the CLOCK, the screen will advance to
Attach the lanyard to the
WEIGHT
pedometer through the (default value is 150 lbs. Range is 45 to 350 lbs).
corner hole
(default value is 60 kg. Range is 20 to 160 kg)
Press MODE to advance by 1 lbs (or 1 kg).
/km
Press RESET to decrease by 1lbs (or 1 kg).
To advance or decrease rapidly, press
respectively for over 2 seconds.
Press SET to confirm your WEIGHT.
/g
This completes the programming. Your pedometer will default to the
STEP and TIME screen for TODAY.
NOTE: The pedometer can be reprogrammed at any time (except under
TOTAL STEPS & 30 days memory mode) by pressing SET for
over 3 seconds. Reprogramming the pedometer will not erase
the 30 Day and TOTAL STEP memory.
Using your Pedometer
(In increments of 1 lbs)
(In increments of 1 kg) Press MODE to cycle through the Pedometer's data views.
(In increments of 0.25 feet)
(In increments of 1 cm)
S
(Up to 999,999 steps or 99 days)
(default value is 3 feet. Range is 1 to 6 feet).
and hold MODE or RESET
Memory Mode
Your pedometer can store up to 30 days of data for steps walked,
calories consumed and distance traveled. At 12:00 a.m. the LCD
resets to zero and the previous day's data is automatically stored
in memory. Even though the daily memory is reset at midnight, the
pedometer will still add each day's detailed data into its 30 day
memory. In addition, the pedometer will also store the steps walked
for up to 999,999 steps or 99 days on its TOTAL Step screen.
Viewing the data stored in memory:
From either the DISTANCE OR CALORIES screen, press the SET
button to view historical data.
Memory Mode
Once in Memory Mode, press the MODE button to between the
STEP, CALORIES and DISTANCE screens.
Press the RESET button to cycle back into historical data by day.
Press the SET button at anytime to exit the Memory Mode.
Memory Mode is off
Motion Lock Mode (for use in vehicles)
In Motion Lock Mode, the pedometer's motion sensor is
deactivated so that no steps or data are mistakenly captured, such
as when driving in a vehicle.
Press & hold MODE for 3 secs.
A lock icon will flash on the
screen.
Press SET to confirm. The lock
icon will remain on screen.
To exit, press & hold MODE for
3 secs. The lock icon will flash
on the screen.
Press SET to confirm. The lock
icon will turn off.
" " Flash
" " Flash