Download Print this page

HP Pavilion 9880 User Manual

Hp pavilion 9880: supplementary guide.
Hide thumbs

Advertisement

V.90 (V.92 Upgradeable)
56K PCI Modem
User's Guide

Advertisement

   Related Manuals for HP Pavilion 9880

   Summary of Contents for HP Pavilion 9880

  • Page 1

    V.90 (V.92 Upgradeable) 56K PCI Modem User’s Guide...

  • Page 2

    Notice: The manufacturer reserves the right to make improvements to the product described in this manual at any time and without notice. All trademarks mentioned in this document are the property of their respective owners. ©2001 This document is copyrighted. All rights are reserved. This document may not, in whole or part, be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form without prior consent, in writing, from the manufacturer.

  • Page 3: Table Of Contents

    Getting the Most From Your V.90 Modem Section One - Introduction ... 4 Section Two - Installing the FAX/Modem ... 6 Section Three - Troubleshooting ... 9 Section Four - AT Command Set... 11 Section Five - Support and Service ... 13 Section Six - Technical Specifications ...

  • Page 4: Section One - Introduction

    Section One - Introduction Congratulations on purchasing your 56k V.90 modem, the latest in communication technology. Your modem represents a new generation of PC communication peripheral devices, combining high-speed Data and Fax functions into a single device. It supports V.90 and K56flex technology for 56kbits/s data transfer rates. This high performance modem connects your computer to all popular modems and fax machines in use today.

  • Page 5

    1.3 Modem Features and Compatibility Your modem is compatible with the following standards. • V.90 / K56flex • Upgradeable to the V.92 standard when finalized • V.32 (9600 bps) • V.32bis (14400 bps) • V.34 (28800 bps) • V.22bis (2400 bps) •...

  • Page 6: Section Two - Installing The Fax/modem

    Section Two - Installing the FAX/Modem 2.1 PCI Modem Installation Your modem may have come pre-installed in your new computer. If so, you may skip this section. CAUTION: Before removing the cover from your computer, turn off and unplug the computer and all attached external peripherals. Prior to removing the modem from its antistatic bag, discharge any static electricity from your body by touching the power supply or the chassis of the computer before removing the modem from its anti-...

  • Page 7

    COM port and IRQ settings to be automatically assigned by the computer and the operating system. 2.3 Installing the Modem in Windows The modem is compatible with all Windows desktop Operating systems from Windows 95 to the present, including: Windows 95 OSR2...

  • Page 8

    For other versions of Windows, you will need a driver installation disk. When Windows identifies the new hardware and asks for a driver disk, select ‘Cancel’ to terminate the Windows ‘new hardware installation’ procedure. Windows will stop the installation procedure and boot normally.

  • Page 9: Section Three - Troubleshooting

    2.5 Testing the Modem To confirm that the modem is working properly after installation, run a modem communication program and set the software for the correct modem COM port. COM port setting information can be found in the Modem Control panel of your Windows operating system.

  • Page 10

    Try connecting to another modem number to ensure the problem is not related to the answering modem. 3.3 Modem makes a connection but no data appears on your screen. 1. Make sure all communication parameters (baud rate, data, stop, and parity bits) are properly configured and are identical on both sides.

  • Page 11: Section Four - At Command Set

    Section Four - AT Command Set 4.1 Executing Commands Your modem is in Command Mode upon power-on and is ready to receive and execute “AT" commands. The modem remains in Command Mode until it makes a connection with a remote modem. 4.2 AT Commands &...

  • Page 12

    Returns country code Low speaker volume Low speaker volume Medium speaker volume High speaker volume Speaker always off Speaker on until carrier detected Speaker always on Speaker off during dialing, on until carrier detected Return online to Data Mode Issue a retrain before returning to Data Mode Pulse dial Result codes enabled Result codes disabled...

  • Page 13: Section Five - Support And Service, Section Six - Technical Specifications

    Section Five - Support and Service If after trying the recommended troubleshooting tips, you are unable to isolate or resolve a problem, you should consult your computer dealer or the place of purchase. Section Six - Technical Specifications Modulation Std.: V.90, K56flex, V.42bis, V.42, V.34, V.32bis, V.32, V.29, V.27ter, V.22bis,V.22, V.21, V.17, Bell212/103 Compression:...

  • Page 14: Section Seven – Regulatory Notices

    Section Seven – Regulatory Notices FCC Compliance This equipment complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company.

  • Page 15

    FCC Fax Branding Statement The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine, or such business, other entity, or...

Comments to this Manuals

Symbols: 0
Latest comments: