EasyPro AquaShine WFL3 Instructions For Operation, Safety, Warranty
Fountain light kit, stainless steel, warm white led light kits, two-light kits for fountains up to 3/4 hp/three-light kits for fountains up to 2 hp, compatible with fountains and aquafloats and kasco vfx or jf series fountains with one piece float
Advertisement
Quick Links
Stainless Steel, Warm White LED Light Kits
Stainless Steel, Warm White LED Light Kits
Two-light kits for fountains up to 3/4 hp
Two-light kits for fountains up to 3/4 hp
Three-light kits for fountains up to 2 hp
Three-light kits for fountains up to 2 hp
Compatible with EasyPro Aqua Fountains and AquaFloats
Compatible with EasyPro Aqua Fountains and AquaFloats
and Kasco VFX or JF series fountains with one piece float
and Kasco VFX or JF series fountains with one piece float
Instructions for Operation •
Instructions for Operation • Safety • Warranty
Thank you for purchasing the AquaShine™ warm white LED fountain light kit.
This kit will transform your fountain into a beautiful night time display. These low
voltage lights use only 11.5 watts per fixture (maximum with full color mix).
Safety and Electrical Connections
1.
Never enter water with electrical connections plugged in or in
operation. Even though units are supposed to be connected to GFCI
protection, it is NEVER recommended to enter water with equipment in
operation.
2. Lights must be attached to matching 2 pin cords and 2 pin 12 volt AC
controller as provided.
3. Never connect the lights directly to a 110 volt or higher outlet.
4. Connect the supplied controller/transformer to a 110 volt receptacle that is
protected by a Ground Fault Circuit Interrupter.
5. Do not modify wiring in any way, quick plug ends must stay intact to
function and should not be replaced with any other connections.
6. Not approved for swimming pool or spa use.
7. All electrical work must be performed by a qualified technician. Always follow
the National Electrical Code (NEC) or the Canadian Electrical Code as well as
all local, state and provincial codes. Failure to follow manufacturer's installation
instructions may result in electrical shock, fire hazard, personal injury or
death, damaged equipment, provide unsatisfactory performance and will void
manufacturer's warranty.
WFL2 • WFL3
Fountain Light Kit
Fountain Light Kit
Safety • Warranty
1
Advertisement
Related Manuals for EasyPro AquaShine WFL3
Summary of Contents for EasyPro AquaShine WFL3
- Page 1 Three-light kits for fountains up to 2 hp Three-light kits for fountains up to 2 hp Compatible with EasyPro Aqua Fountains and AquaFloats Compatible with EasyPro Aqua Fountains and AquaFloats and Kasco VFX or JF series fountains with one piece float and Kasco VFX or JF series fountains with one piece float Instructions for Operation •...
-
Page 2: General Instructions
• Stainless steel housing • Epoxy filled fixture with pigtail and waterproof quick connect end General Instructions Inspect the box and check for damaged or missing parts. Contact your EasyPro supplier if products are damaged in shipping. Parts Included WFL2 Two Light Kits •... - Page 3 LED Light Kit Assembly Instructions for 1/2 and 1 hp Aqua Fountains 1. Attach the light fixture to the supplied brackets. The nylock nut comes attached to the bracket for shipping. You will need to remove nylock nut and install the yoke of the light fixture to the bracket.
- Page 4 LED Light Kit Assembly Instructions for 1/2 to 1 hp Kasco VFX, AF and JF Series Units 1. Attach the light fixture to the supplied brackets. The nylock nut comes attached to the bracket for shipping. You will need to remove nylock nut and install the yoke of the light fixture to the bracket.
- Page 5 LED Three Light Kit Assembly Instructions for 2 hp Kasco VFX, AF and JF Series Units Actual light fixture may vary slightly from fixtures below. 1. For 2 hp Kasco units use the 3/4" pan head screws from hardware pack labelled LKH-KBW with nylock nut and smaller washer.
-
Page 6: Setting The Timer
Setting the Timer Mount the weatherproof controller box in a secure location near a power supply and plug into 110 volt outlet. The controller is weatherproof and does not need to be protected from the weather. Example Program Functions PROGRAM Example Manual Functions AUTO... -
Page 7: Service And Maintenance
Operation Instructions for Manual Function 1. Be sure the controller is plugged into 110 volt GFCI protected outlet. 2. Remove clear plastic cover from timer. Keep cover safe and replace when finished. 3. Unlock the timer by pressing the “C/R” button four times. This removes the “a” character in lower left corner of the display screen. - Page 8 EasyPro shall not be held liable for any loss of fish, plants or any other livestock as a result of any failure or defect of this Product. This warranty gives you specific legal rights, and you may also have other rights that vary from State to State.