IMPORTANT
60 - ABF3448 - ABF3460 - ABF3642 - ABF3648 - ABF3660 - ABF3672 - ABF4260 - ABF4860
ARRELAGE.
/
INSTALL TILING FLANGE.
Il est impératif de lire ce manuel d' installation au complet et de bien comprendre toutes les étapes d'installation de
votre nouvelle douche. Il est fortement recommandé de porter des lunettes de sécurité lors de l'installation. Avant
l'installation de la base, toute l'ossature et la plomberie doivent être complétées conformément aux instructions.
S'il s'agit de travaux de rénovation, les surfaces murales existantes doivent être en levées pour installer l'ossature
la bride de carrelage afin
appropriée. Les murs extérieurs doivent être isolés adéquatement et inclure un coupe-vapeur conformément aux codes
ant en silicone le long du
du bâtiment.
It is imperative to read this installation manual completely and understand all the steps for installing your new shower. It
le flange so to apply a line of
is highly recommended to wear safety glasses during installation. Prior to installation of base, all framing and plumbing
annel.
work must be completed in accordance with this instruction sheet. For renovation work, existing shower surfaces must
be removed to accommodate framing requirements. Ensure that outer wall are properly insulated, and that a vapor
arrelage sur la paroi
barrier has been installed in accordance with established building codes.
s vis autopercante #6 x 1"
er wall of the base
OUTILS ET MATÉRIAUX REQUIS / TOOLS AND MATERIALS REQUIRED
1"
PERÇEUSE
DRILL
1. PREPAREZ LA PLOMBERIE /
PREPARE DRAINING PIPE
/
E D'ÉVACUATION.
Percez le plancher [Ø5"(12.7cm) à Ø6"(15.2cm)] pour la plomberie d'évacuation.
1A
Le tuyau de renvoi de 2" (5.0cm) doit dépasser de 1/2" (1.27cm) du placher
existant. Les dimensions D et E du mur au centre du drain sont donner dans le
cm) à Ø6"(15.2cm)] pour
tableau. Vérifier votre base pour les dimensions finales.
e tuyau de renvoi de
1/2"(1.27cm) du placher
Cut floor [Ø5"(12.7cm) to
Ø6"(15.2cm)] to accommodate
du mur au centre du
plumbing. The 2" (5.0cm)
imensions finales.
drain pipe should project
1/2"(1.27cm) above floor line.
"(15.2cm)] to accom-
Dimensions D and E from wall
0cm) drain pipe should
to center of drain are in the
oor line.
table. Verify your base for
om wall to center of
final dimensions.
ensions.
Déposer la base en place. Assurez-vous que l'emplacement de la plomberie
1B
d'évacuation soit parfaitement aligné avec le drain de la base. Ensuite, enlevez
. Vérifiez que
la base.
ie d'évacuation
est
e. Enlevez la base.
Place the base. Make sure
the exhaust plumbing
draining pipe location
f the base drain.
location is perfectly aligned
with the drain of the base.
Then, remove the base.
* INSTALLATION DU TYPE SEUIL DOUBLE ILLUSTRÉ
* DOUBLE THRESHOLD INSTALLATION TYPE SHOWN
1B
MÈCHE 3/16˝
SILICONE
DRILL BITS 3/16˝
SILICONE
PREPARE DRAINING PIPE.
Manuel d'installation pour base de douche en acrylique
CRAYON
RUBAN À MESURER
PENCIL
TAPE MEASURE
Dim E
Dim D
Acrylic shower base installation guide
NIVEAU
DRAIN
CIMENT ÉGALISATEUR ou MORTIER
LEVEL
DRAIN
FLOOR LEVELING COMPOUND
3636BA
3636BLR
4832BA
4832BL
4832BR
4836BA
4836BL
4836BR
4836BLL(S)
4836BRL(S)
4836BALL(S)
4836BARL(S)
6030BA
6032BA
6032BAL
6032BAR
6032BL
6032BR
6032BLL(S)
6032BRL(S)
6032BALL(S)
6032BARL(S)
6036BA
6036BL
6036BR
6036BLL(S)
6036BRL(S)
6036BALL(S)
6036BARL(S)
5
C im en t
ég al is at eu r
F lo or
le ve lin g
co m po un d
or MORTAR
D
E
18"
18"
16"
24"
18"
24"
18"
5 5/32"
15"
30"
16"
30"
16"
7 7/8"
16"
8"
16"
5 5/32"
18"
30"
18"
8"
18"
5 5/32"