Sealey 3040AY Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction
manual
1. SAFETY
Ensure the jack is in sound condition and good working order. Take action for immediate repair or
9
replacement of damaged parts. Use genuine parts only. The use of improper parts may be dangerous
and will invalidate the warranty.
Locate the jack in a suitable, well lit working area.
9
Keep working area clean and tidy and free from unrelated materials.
9
Use jack on level and solid ground, preferably concrete.
9
Avoid tarmacadam as jack may sink in. Chock wheels of vehicle.
9
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear
9
(or "PARK" if automatic).
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow
9
for vehicle tilting.
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
9
Ensure there are no passengers in the vehicle.
9
Place jack under only those lifting points recommended by vehicle manufacturer (see vehicle handbook).
9
Check that the lifting point is stable and centred on the jack saddle.
9
Ensure the jack wheels are free to move and that there are no obstructions.
9
▲ DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
Ensure there are no persons or obstructions beneath the vehicle before lowering.
9
Use suitable axle stands under the vehicle before proceeding with any task.
9
Use a qualified person to lubricate and maintain the jack.
9
Ensure that only hydraulic jack oil is used in the jack.
9
DO NOT operate the jack if damaged.
8
DO NOT allow untrained persons to operate the jack.
8
DO NOT exceed the rated capacity of the jack.
8
DO NOT allow the vehicle to move during lifting or lowering, or use the jack to move the vehicle.
8
DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8
DO NOT work under the vehicle until appropriately rated axle stands have been correctly positioned.
8
DO NOT use the jack for purposes other than that for which it is intended.
8
DO NOT top up hydraulic system with brake fluid. Use hydraulic jack oil only.
8
DO NOT adjust the safety overload valve.
8
When not in use store jack, fully lowered, in a safe, dry, childproof area.
9
2. INTRODUCTION
Single-piece hydraulic units with heavy base design and large jacking saddle. Universal joint release mechanism allows safer, more controlled
lowering of the jack. Rocket Lift feature brings lifting arm into contact with jacking point with just a few pumps. Polyurethane wheels for smoother
manoeuvrability and prevents damage to workshop floor. Magnetic wheel nut retention tray. Protective jack handle sleeve helps prevent accidental
damage to car bodywork when pumping the handle. Range available in five different colours. 2 Year Guarantee - 2nd year subject to T&Cs and
registration on website (www.sealey.co.uk).
3. SPECIFICATION
Model No: ................................................ 3040A.V2 SERIES
Capacity ...................................................................... 3tonne
Consumable Parts: ....Replacement Rubber Jack Pad - JP17
Length: ....................................................................... 740mm
Max. Chassis Height: ................................................. 162mm
Max. Saddle Height: ................................................... 533mm
Min. Saddle Height: .................................................... 100mm
4. ASSEMBLY
4.1. Insert the upper handle into the lower handle. Refer to Parts List.
4.2. Undo the handle socket screw Fig.1-B until it no longer protrudes into the handle socket.
4.3.
Insert the pump handle into the handle socket, engaging the square drive of the release valve.
4.4.
Ensure that the handle is correctly inserted into the socket, then tighten the handle socket screw Fig.1-B.
© Jack Sealey Limited
TROLLEY JACK 3TONNE ROCKET LIFT
MODEL NO:
Wear safety
footwear
ASSEMBLY
Original Language Version
3040A.V2 SERIES
TJL3
Apply
h ndbr ke
1 3 5
2 4 R
Use on h rd level floor
Chock
wheels
Never
exceed
j ck c p city
Close
Lower
R ise
OR
Lift & twist
to lower
R ise
Use suit ble xle st nds
X2
w w w . s e l e y . c o . u k
3040A.V2 Series Issue:3 (2,4) 06/10/21