Littfinski Daten Technik COL-10 Assembly Instruction

L D T
ittfinski aten echnik (
Assembly Instruction
Components for the Transponder Technology (RFID)
Transponder-Reader
COL-10
COL-10-B
The Transponder Reader COL-10 supplied with a
rugged external PC-board antenna is suitable for the
reading of 125 kHz transponder (RFID-Tag) according
EM-4102.
This product is not a toy! Not suitable for children under 14 years of age!
The kit contains small parts, which should be kept away from children under 3!
Improper use will imply danger of injuring due to sharp edges and tips! Please store
this instruction carefully.
Introduction:
You have purchased a kit for your transponder system supplied
within the assortment of Littfinski DatenTechnik (LDT).
These kits are of high quality and easy to assemble.
We are wishing you having a good time for assembling and
application of this product!
General:
Tools required for the assembly
Please assure that the following tools are available:
• a small side cutter
• a mini soldering iron with a small tip
• solder tin (if possible 0.5mm diameter)
Safety Instructions
• All electrical and electronic components included in this kit
shall be used on low voltage only by using a tested and
approved voltage transducer (transformer). All components
are sensitive to heat. During soldering the heat shall be applied
for a very short period only.
• The soldering iron develops a heat up to 400°C. Please keep
continual attention to this tool. Keep sufficient distance to
combustible material. Use a heat resistant pad for this work.
• This kit consist of small parts which can possibly be swallowed
from children. Children (especially under 3 years) shall not
participate on the assembly without supervision.
LDT
)
070051
Part-No.:
>> kit <<
Set-Up:
For the board assembly please follow exact the sequence of the
below assembly list. Cross each line off as done after
completing the insertion and the soldering of the respective part.
For the diodes please keep special attention to the correct
polarity (marked line for the cathode).
With reason to different makes of electrolytic capacitors you
will find different markings of the polarity. Some are marked with
"+" and some are marked with "-". Each capacitor has to be
assembled to the board that the marking on the capacitor is in
correspondence with the marking on the pc-board.
Light emitting diodes have to be assembled that the long wire
of the diode corresponds to the mark "+" on the pc-board. Before
assembly please slip the distance spacer onto the connection
wires.
For the correct assembly of the address switch please attend to
the "on" mark on the case and on the pc-board.
Integrated circuits (IC`s) are either marked with a half round
notch on one end or a printed point for the correct mounting
position. Push the IC`s into the correct socket assuring that the
notch or the printed point is corresponding to the half-rounded
marking on the pc-board.
Please attend to the sensitivity of the IC`s to electrostatic
discharge which will cause immediate damage of the IC. Before
touching those components please discharge yourself by
contacting an earthed metal (for example an earthed radiator) or
work with an electrostatic safety pad.
Assembly List:
Pos. Qty. Component
1 1 Printed circuit board
2 1 Diode 1N4003
3 1 Diode 1N5819
4 3 Diodes 1N4148
5 1 Resistor 82kOhm
6 1 Resistor 47kOhm
7 2 Resistors 470Ohm
8 1 Resistor 10kOhm
9 1 Resistor 470kOhm
10 1 IC-Socket 20polig
11 2 IC-Sockets 8polig
12 2 Electrolytic cap. 220uF/35V attend to the polarity!
13 1 Coil 330uH
14 1 Multi-Fuse R050
15 6 Capacitors 100nF
16 1 Capacitor 220nF
17 1 Capacitor 33nF
18 1 Capacitor 6800pF
19 3 Capacitors 10nF
20 1 Resonator 4MHz
21 1 LED plus distance spacer
22 4 Clamps 2poles
23 1 Address Switch
24 1 IC: AT...2313
25 1 IC: LM2574
26 1 IC: MAX483
27
Subject to technical changes and errors. © 08/2019 by LDT
Remarks Ref.
attend to the polarity! D1
attend to the polarity! D2
attend to the polarity! D3...D5
gray-red-black-red R2
yellow-violet-black-red R3
yellow-violet-black-black R4, R5
brown-black-black-red R6
yellow-violet-black-orange R7
IC1
IC2, IC4
C1, C2
gold-brown-red-red L1
MF1
100nF = 104 C3...C8
220nF = 224 C9
33nF = 333 C10
C11
10nF = 103 C12...14
CR1
attend to the polarity! LED1
KL1...4
attend to the polarity! SW1
attend to the polarity! IC1
attend to the polarity! IC2
attend to the polarity! IC4
Final control
Made in Europe by
Littfinski DatenTechnik (LDT)
Bühler electronic GmbH
Ulmenstraße 43
15370 Fredersdorf / Germany
Phone: +49 (0) 33439 / 867-0
Internet: www.ldt-infocenter.com
Done