Sealey PTBJ2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Instruction
Manual
1. SAFETY
 Inspect and lubricate the jack regularly to ensure it is in good working order and condition. DO NOT use the jack if damaged or a fault is
suspected - check Section 6 Troubleshooting. If necessary, repair immediately or replace damaged parts.
 Use recommended parts only. The use of unauthorised parts may be dangerous and will invalidate your warranty.
 Ensure the work area is clean, tidy and free from unrelated materials and has adequate lighting.
 Use jack on level and solid ground, preferably concrete. Avoid tarmacadam since jack may sink in.
 Park the vehicle and apply hand brake (if automatic, place in "Park" mode). Switch off the engine and place chocks under the wheels.
 Ensure a minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc. to allow for tilting during jacking.
 Ensure all persons are out of the vehicle before jacking. DO NOT enter vehicle whilst it is supported on the jack or axle stands.
 Check vehicle weight and recommended lifting points by referring to the vehicle owner's manual. Ensure the lifting point is not corroded.
 Check lifting point is centred and stable on jack saddle. Position jack so as to avoid operating it from under the vehicle.
▲ DANGER! Use the jack for lifting only, NOT for supporting the lifted load. ALWAYS USE ADEQUATELY RATED AXLE STANDS.
 Keep hands etc. clear of moving parts during raising and lowering of the vehicle.
▲ DANGER! Roadside wheel changing is hazardous. Be extra vigilant, you may not be able to avoid jacking on tarmacadam. Get everyone
out of the vehicle. NEVER go under vehicle. Traffic may cause vehicle to rock. If in doubt call professional help.
 When changing a wheel, loosen wheel nuts/bolts slightly prior to jacking vehicle. Screw wheel nuts/bolts back before lowering the vehicle.
Tighten finally when vehicle is fully lowered.
 Use a qualified person to lubricate and maintain the jack. Confirm that only recommended hydraulic jack oil is used during maintenance.
DO NOT exceed the rated capacity of the jack and DO NOT operate the jack beyond its maximum pump stroke.

 WARNING! DO NOT allow the vehicle to move, or try to start the engine, when the vehicle is jacked up.
 DO NOT jack a vehicle if it may result in the spillage of fuel, battery acid, or other dangerous substances.
 DO NOT place any part of your body under vehicle whilst it is supported by the jack. Wait until adequately rated axle stands have
been correctly positioned.
 DO NOT modify the jack in any way. DO NOT use the jack for any other purpose than that for which it is designed.
 DO NOT top up jack with brake fluid. Use hydraulic oil only. DO NOT adjust the safety overload valve (fig.1.4.).
 Ensure there are no persons or obstructions beneath the vehicle before lowering.
 Clean and store the jack securely with the ram in the down position. DO NOT leave the ram extended. Ensure storage area is dry.
2. INTRODUCTION
Telescopic hydraulic ram allows a reduced closed height without compromising maximum lift height. Made in the EU and fitted with safety overload
valve. One-piece steel base, reservoir and pump cylinder design gives added strength. Supplied with zinc coated handle. Model No's PTBJ12 -
PTBJ20 fitted with carrying handle.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . PTBJ2. . . . . . . . . . . . . PTBJ5 . . . . . . . . . . . . . PTBJ12. . . . . . . . . . . . .PTBJ20
Capacity: . . . . . . . . . . . . . . 2tonne . . . . . . . . . . . . . 5tonne . . . . . . . . . . . . . 12tonne . . . . . . . . . . . . .20tonne
Minimum Height: . . . . . . . . 145mm . . . . . . . . . . . . 215mm . . . . . . . . . . . . 245mm . . . . . . . . . . . . . 180mm
Maximum Height: . . . . . . . . 360mm . . . . . . . . . . . . 515mm . . . . . . . . . . . . 571mm . . . . . . . . . . . . . 385mm
Hydraulic Lift: . . . . . . . . . . . 165mm . . . . . . . . . . . . 300mm . . . . . . . . . . . . 326mm . . . . . . . . . . . . . 205mm
Screw Extension: . . . . . . . . 50mm . . . . . . . . . . . . . n/a . . . . . . . . . . . . . . . . n/a . . . . . . . . . . . . . . . . . . . . .n/a
© Jack Sealey Limited
INSTRUCTIONS FOR:
PREMIER TELESCOPIC BOTTLE JACKS
2tonne, 5tonne, 12tonne, 20tonne
PTBJ2, PTBJ5, PTBJ12, PTBJ20
PART NO's:
Wear Safety
Footwear
Original Language Version
PTBJ2,PTBJ5,PTBJ12,PTBJ20 Issue: 1 - 06/10/16