Patterson Medical EC Quick Start Manual

, CONTRA ANGLE SHEATH
043-4126 EC, CONTRA ANGLE SHEATH
043-2542 E4R, CONTRA ANGLE SHEATH
peration Manual
ore use
s the safety of all patients.
• The number one priority is the safety of all patients.
during use, stop immediately. Report this to the • If an abnormality occurs during use, stop immediately. Report this to the
was purchased.
Patterson branch where it was purchased.
er the sheath.
• Do not disassemble or alter the sheath.
to a hard surface.
• Do not drop the sheath onto a hard surface.
n, sound, temperature rise, bur wobble and other
• Always watch for vibration, sound, temperature rise, bur wobble and other
abnormalities.
er the driver unit has completely stopped.
• Disconnect the sheath after the driver unit has completely stopped.
son heads.
• The device accepts Patterson
®
r immerse in highly acidic water or sterilizing
• Do not wipe with, clean or immerse in highly acidic water or sterilizing
solutions.
1. Specifications
EC
(043-4126) Product number
40,000 rpm
Allowable max. speed
1：1
Speed reduction ratio
l of Head onto/from Contra Angle Sheath 2. Installation/Removal of Head onto/from Contra Angle Sheath
d with that of the sheath. Then install the head
Align the Clutch of the head with that of the sheath. Then install the head
Union Nut counterclockwise with your fingers.
onto the sheath, turning the Union Nut counterclockwise with your fingers.
tch
nt if it cannot be smoothly installed onto or
• Never use the attachment if it cannot be smoothly installed onto or
ght nosecone or the contra angle sheath. In
removed from the straight nosecone or the contra angle sheath. In
he Patterson Service Center.
such a case, consult the Patterson Service Center.
g
3. Cleaning and Drying
Exterior
Cleaning and Drying the Exterior
ning devices is not recommended for the cleaning
The use of automated cleaning devices is not recommended for the cleaning
of Contra Angle Sheaths.
running water
Wash the handpiece under running water
elow. (Water
following the procedures below. (Water
min; water should
condition: ≤100°F, ≥3.5L/min; water should
rinking water)
be of the same quality as drinking water)
s of the
- Clean the external surfaces of the
tled toothbrush
handpiece with a soft bristled toothbrush
for 15 seconds or more.
rtion hole for 15 - Clean around the bur insertion hole for 15
n interdental seconds or more, using an interdental
mm) that
brush (wire thickness 0.7mm) that
16409.
conforms to size 4 in ISO 16409.
g (natural office
Under appropriate lighting (natural office
, inspect the
lighting, 500 lx or higher), inspect the
her debris. If any visible debris remains, repeat
handpiece for blood or other debris. If any visible debris remains, repeat
piece is visually clean.
the process until the handpiece is visually clean.
dual moisture is present, wipe off with dry cloth
After cleaning, if the residual moisture is present, wipe off with dry cloth
essed air (≤50.75psi) until there is no moisture in
or blow it off with compressed air (≤50.75psi) until there is no moisture in
the interior and exterior.
ompressed air, cover the handpiece with cloth to
When blowing off with compressed air, cover the handpiece with cloth to
r. Proceed to 4: Cleaning and Lubrication. prevent scattering of water. Proceed to 4: Cleaning and Lubrication.
135˚C/
275˚F
Operation Manual
Caution before use
E4R
(043-2542)
40,000 rpm
4：1
Union Nut
Installation
Clutch
Caution
: AUTOCLAVABLE
OM-CZ490E 002
heads.
®
EC
(043-4126)
40,000 rpm
1：1
135˚C/
: AUTOCLAVABLE
275˚F
OM-CZ490E 002
E4R
(043-2542)
40,000 rpm
4：1
Union Nut