Tapmaster 1720 Installation Instructions

TROUBLE SHOOTING
Symptom Possible Cause
The hot or cold water is very Pinched tubing
slow to turn on
The hot or cold water is very Pinched tubing
slow to shutoff or will not
shutoff
Noise from the Valve Blocks The Valve Block may have
while the water is running excessive debris trapped
under the Filter-screen
Noise from the Valve Blocks Air in the system
when turning water on and
off
For further information: www.tapmaster.ca or call 800-791-8117
FIVE YEAR LIMITED WARRANTY
Congratulations on your purchase of TAPMASTER Hands Free Faucet Controller!
TAPMASTER products are thoroughly tested before shipment and are warranted to be free of
defects in material and workmanship for five years from the date of original purchase. The sole
obligation of Tapmaster Incorporated under the warranty is to provide replacement parts or at its
option to repair the defective product or to provide the replacement product. Replacement parts
furnished in fulfillment of this warranty are warranted only for the unused portion of the original
warranty. Labor and shipping charges are not included.
Warranty conditions - The five year warranty is subject to exclusions and limitations as stated
below:
Warranty extends only to defects which occur during normal use and intended applications and
does not extend to damage to products or parts resulting from alteration, repair, modification or
faulty installation. This warranty does not cover damage resulting from water borne debris or
from media other than clean potable water. Tapmaster Incorporated makes no other express
warranty on this product, all implied warranties including any implied warranty of merchantability
and fitness for a particular purpose are hereby disclaimed and excluded. In no event shall Tap-
master Incorporated be liable for special, incidental or consequential damages resulting from the
use of this product or arising from breach of warranty or contract, negligence, loss of time,
inconvenience or loss of use of equipment.
Tapmaster Incorporated
#3, 1470 28 Street NE
Calgary, Alberta
T2A 7W6
Remedy
Check control tubing (yellow
and blue lines)
Check control tubing (green
and blue)
Service the Valve Blocks
Operate the pedal on and off
rapidly to clear air from the
valves.
PH: 800-791-8117
FAX: 403-275-5928
Web: www.tapmaster.ca
Rev 3.0 E-mail: info@tapmaster.ca
- -
4
INSTALLATION INSTRUCTIONS: Models 1720, 1722 & 1710
CAUTION - READ BEFORE INSTALLATION
Tapmaster Incorporated will not be held liable for damage to property or persons resulting from improper installation of this product
any part of the installation process, please contact us for assistance or consult a professional tradesperson before installation.
• Water lines must be flushed prior to installation
• Do not install if control tubes are damaged in any way
• Control tubes are pressurized after installation. Do not
expose tubing to excessive heat, unsealed chemicals, or
physical damage
This illustration shows a typical installation for the Model 1720 Tapmaster. The valve blocks are
-point along the 3/8" supply tubing. In this case it will be necessary to obtain a 3/8" x 3/8"
compression connector (available at most hardware stores)
water lines. Other plumbing arrangements may be encountered where larger than 3/8" O.D. tube
sizes are used. In these situations reducing adapters
obtained to permit installation of the Tapmaster.
Although the Tapmaster will work with virtually any faucet, faucets with handles that give a visual
reference for flow and temperature are recommended. Cabinet doors will also vary in design and
construction. Doors with spring loaded hinges are recommended. However, mechanical and
magnetic latches will work equally well as long as there is some play in the mechanism to
accommodate the 1/32" stroke of the pilot/actuator valve.
To operate the Tapmaster simply press against the cabinet door
with your knee or leg and set the faucet open to the desired flow
and temperature. By releasing the door, the Tapmaster shuts off
the water flow to the faucet. Once the faucet has been adjusted
it should be left open.
The Tapmaster does not alter the appearance of the faucet,
therefore a removable decal is provided which may be located on
any hard smooth surface near the faucet to alert people to its
method of operation. Alternately, simply attaching a piece of tape,
string or an elastic band to the faucet handle will remind the end-
user the faucet is Tapmaster equipped.
CSA-B125.1-18 U.S. 5,505,227, 6,254,057,
ASME A112.18.1-2018
NFS/ANSI 61-2016
NSF/ANSI 372-2016
International & Other Patents
LOW LEAD CONTENT DRINKING WATER
.
• Use of substitute tubing voids manufacturer warranty and
liability
• Do not expose valves to thread sealants/plumbers putty
• Operating Range: 0 - 125 psi (8.6 bar) Max, 140° F
(60° C) Max
GENERAL
connected in-line on the hot and cold water
supplies with 3/8" O.D. compression fittings. The
pilot/actuator valve is mounted about knee
height on the inside wall of the cabinet opposite
the door hinge. The control tubing is routed in
between the valves. Water flow to the faucet is
activated by pressing with the knee or leg against
the cabinet door.
Installation for the 1722 and 1710 models is
essentially identical. The Model 1722 comes with
two pilot/actuator valves and is generally used on
island cabinets required control from either side.
The Model 1710 comes with one valve block
attached to a pilot/actuator valve and is typically
used on mixed or single line water supplies.
Installations will vary according to the design of
the cabinet, type of faucet and plumbing
hardware. In some cases it may be simpler to
connect the valve blocks at some convenient mid
to connect the inlet fitting into the
(available at most hardware stores)
OPERATION
PATENT NUMBERS
6,382,585
Canadian 2,109,684
European 0654628
Pending
If you are uncertain about
must be