Jasco UltraPro 54850 Quick Start Manual

54850 & 54851
OUTDOOR SIMPLE-SET PLUG-IN
GROUNDED OUTLET TIMER
IF MOUNTING OUTDOORS
1. Mount the timer on a wall near a GFCI receptacle using a screw or nail. Install timer
as far above ground level as possible with receptacle facing downward. Do not
install where timer can be immersed or where water will splash or drip onto
receptacle. Screw or nail head must extend at least 3/16in. from the wall (nail or
screw not included).
2. Hang the timer from the hole at the top of the unit.
SETUP
1. If numbers are difficult to read or not visible
on-screen, plug timer into an outlet and let timer
charge for 1 hour. Once charged, press the reset
( ) button in the lower right corner using a
toothpick or pencil.
2. Use up ( ) and down ( ) arrows to set
current time. Take note of the AM/PM setting.
Note: When daylight saving time occurs use the
up ( ) and down ( ) arrows to adjust the
time by 1 hour.
PROGRAMMING OPTIONS
DEFAULT TIMER
There are two ON/OFF times available
with preset default times. To activate
default times, simply press ON TIME or
OFF TIME button so the arrow (
) next
to the setting is visible on the display. To
deactivate the default timer, press and
release the button. The arrow next to the
setting will disappear.
CUSTOMIZED TIMER
On time: Press and release either ON TIME button to
enter custom setting mode. The default on time
flashes. Use arrow buttons ( ) to set the desired
on time. Press the ON TIME button or wait 5 seconds
to set. If no button is pressed within 5 seconds, the
default timer will be set and the display will return to
clock mode. If you set the on time earlier than the
current time, it will not turn on until the next day at
the scheduled time.
Note: Mode indicator ( ) will move under SET while
programming, then back to CLOCK if it times out or
after on time is set.
Off time: Press and release either OFF TIME button to
enter custom setting mode. The default off time
flashes. Use arrow buttons ( ) to set the desired
off time. If no button is pressed within 5 seconds, the
default timer will be set and the display will return to
clock mode. Press the OFF TIME button or wait 5
seconds to set.
Note: When an on time or off time is set, the active
program indicator ( or ) will appear on the screen
beside the setting. Programs may run individually or
simultaneously.
READ IT OR WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit https://byjasco.com/54850i
CLOCK SET
ON
OFF
1
1
2 2
AM
ON OFF
TIME 1 TIME 1
ON OFF
TIME 2 TIME 2
R
RESET
BUTTON
SET
CLOCK
ON
OFF
1
1
2 2
AM
ON OFF
CLOCK SET
TIME 1 TIME 1
ON OFF
1
1
ON OFF
2
2
AM
TIME 2 TIME 2
R
ON TIME 1 OFF TIME 1
ON OFF
5:00PM 12:00AM
TIME 1 TIME 1
ON TIME 1 OFF TIME 2
ON OFF
6:00PM 6:00AM
TIME 2 TIME 2
CLOCK SET
R
ON
OFF
1
1
2
2
AM
CLOCK SET
ON OFF
ON OFF
TIME 1 TIME 1
1 1
2
2
AM
ON OFF
TIME 2 TIME 2
R
CLOCK ON OFF SET
TIME 1 TIME 1
ON
OFF
1
1
2
2
AM
ON OFF
TIME 2 TIME 2
R
CLOCK SET
ON OFF
ON OFF
TIME 1 TIME 1
1 1
2
2
AM
ON OFF
TIME 2 TIME 2
R
ON OFF
TIME 1 TIME 1
ON OFF
TIME 2 TIME 2
R
FCC/IC - EN
Supplier Declaration of Conformity | Model #: 54850, 54851 | Jasco Products Co.,
10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the receiver
is connected.
— Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
SPECIFICATIONS
125VAC, 50/60Hz
10A 1250W general/resistive
5A 625W tungsten
1/4HP motor type 3R
Works with dimmable LED and CFL bulbs
WARNING
RISK OF ELECTRICAL SHOCK RISK OF FIRE
• PLUG DIRECTLY INTO A • DO NOT USE TO CONTROL
GFCI PROTECTED OUTLET APPLIANCES THAT CONTAIN
HEATING ELEMENTS
• UNPLUG TIMER BEFORE
(COOKING APPLIANCES,
CLEANING
HEATERS, IRONS, ETC.)
• FULLY INSERT PLUG
• DO NOT EXCEED
• KEEP AWAY FROM
ELECTRICAL RATINGS
CHILDREN
• DO NOT USE IF DEVICE OR
• NOT FOR WATER
CORD IS DAMAGED
IMMERSION
• DO NOT USE WITH AN
• SUITABLE FOR INDOOR
EXTENSION CORD
AND OUTDOOR LOCATIONS,
STORE INDOORS WHILE
NOT IN USE
MADE IN CHINA/HECHO EN CHINA
Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 2-year limited warranty. Visit www.byjasco.com for
warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between
7AM-8PM M-F, Central Time.
©JASCO 2020 | 54850, 54851 | 09/08/20 v1
MTS 53003