Nidac Presco 1 Series Installation Manual

PRO2410
"Series 1"
Indoor/Outdoor 12 to 24V DC
Proximity Reader
Installation Manual
1
OVERVIEW
The Presco™ PRO2410 Proximity Reader is an advanced, self
contained RFID (Radio Frequency IDentification) contactless
reader. It is capable of interfacing to either a Wiegand input
control panel or to Nidac's range of Presco™ PAC decoders.
The encapsulation makes it suitable for outdoor environments
and the narrow styling makes the PRO2410 suitable for door
frame mounting as well as other mounting positions.
OPERATION
Connected to a Presco™ PAC decoder
The LED on the reader is red when ready to read a Presco™
prox card. When a card is presented to the front of the reader
the LED momentarily turns orange to indicate that the PRO2410
has read it. The code is then transmitted to the PAC decoder.
If the card is valid the PRO2410 will respond with 1 or 2 short
beeps and the LED will change to green (provided the blue wire
is connected as shown in the wiring diagram) for the time the
ELC relay is active (door is released).
If the card is invalid the PRO2410 will respond with a "blarp"
(long beep) and the LED will remain red.
Connected to a Wiegand controller
The LED on the reader is red when ready to read a Presco™
prox card. When a card is presented to the front of the reader
the LED momentarily turns orange and the internal buzzer gives
a short beep to indicate that the PRO2410 has read it. The code
is then transmitted to the Wiegand controller.
The LED can be made to change colour to green by the
controller applying negative signal (0 to 2V) to the violet wire or
a positive signal (2.5 to 28V) to the blue wire.
The buzzer can be made to sound by applying a negative signal
(0 to 2V) to the brown wire.
N761
st
Edition
1
3
™ WARRANTY
Nidac Security Pty. Ltd. will repair or replace this product if
proven to be faulty (excluding accidental or malicious damage)
under the 36 month warranty offered from the date of purchase.
As Nidac Security Pty. Ltd. or its agents do not perform the final
installation, inspection or training in the use of this product, they
cannot be held liable for injury, loss or damage directly or
consequentially arising from the use or misuse of this product.
Presco™ is a registered Trade Mark belonging to Nidac Security
Pty. Ltd. The Presco™ system is protected by provisional and
pending patents in various countries including Australia.
The software design is protected internationally and remains the
intellectual property of Nidac Security Pty. Ltd.
Design improvement and specifications are subject to change
without notice. All designs are copyright 1992 - 2011.
Designed and Manufactured by:
NIDAC SECURITY PTY. LTD.
2 Cromwell Street
Burwood, Victoria
Australia 3125
100%
Revision 1.0
SPECIFICATIONS
Voltage:-
Current:-
Size:-
Weight:-
Outputs:-
Read Range:-
Wiring Distance:- PRO2410 to Presco™ PAC Decoder = 1Km.
Excitation Frequency:-
Operating Temperature:- 0C to 70C.
36 month (3 year) manufacturer's warranty.
Designed and manufactured in Australia.
Phone: 61 3 9808 6244
Fax:
"When you're serious about security"
2
PRO2410 Series 1 Instructions.docx 3/11/11
8 to 28 Volts D.C.
50mA max @ 8 Volts D.C.
35mA @ 12 Volts D.C.
20mA @ 24 Volts D.C.
82.5mm x 43.7mm x 16.3mm.
80 grams.
26 bit Wiegand, Pulse Width = 50s,
Pulse Separation = 2ms.
and Presco™ PAC decoder format.
Up to 11cm (4 ⅓").
Unshielded cable, 100max. return resistance
on DTA line. To achieve distances greater than
100m the PRO2410 may require a separate local
power supply depending upon the thickness of
the cable used.
PRO2410 to Wiegand controller, shielded
cable must be used.
Wire Gauge Wiegand Wiring Distance
22 AWG 150m (490 ft)
24 AWG 100m (330 ft)
26 AWG 60m (195 ft)
28 AWG 40m (130 ft)
125 ± 5 KHz.
4
61 3 9808 9335