NK THE MANUFACTURER IS ACTUALLY , C-ENCE IS THE MODEL NAME T1 User Manual

Thank you for purchasing a Cadence T1 Watch from NK. The Cadence is the complete rower's
timepiece; it is a full-functioning digital watch, as well as a wireless rate meter. The patented tilt-
switch technology calculates stroke rate based on the feathering interval. There are no wires to
install, making the Cadence an ideal tool for rowers who use different boats. Coaches and spectators
can press the large rate button to take stroke rates at any time. It's even possible to measure rates
with one hand by simulating the feathering motion with the watch hand - great when driving a
motorboat.
Button Functions:
Illuminate
Backlight
Start & Stop
Chronograph
Take Manual Rate(s),
Advance to Next Setting
Take Splits,
Cycle Modes,
Reset Chronograph
Set Clock/Alarm,
Recall Chronograph

TIME MODE

Illuminate
Increase
Backlight
Setting
Advance to
Next Setting
Decrease
Enter & Exit Setting
Mode
To set the clock and calendar:
"HOLD TO SET" will be displayed, with a beep when entering the Time
1. Hold the Set button
for 3 seconds to set. Setting Mode. The first setting (hours) will blink, indicating that the
value may be changed.
2. Press the + button Hold the + or - to increase or decrease the value quickly.
to increase or - to
decrease.
3. Press the >> button Settings: Hour, minutes, seconds, year, month, date, 12-hour or 24-hour
format, date format (MM-DD or DD-MM), and hourly chime (on or off).
to advance to the
next setting.
4. Repeat until all
Press the Mode button at any time to exit Date/Time setting. If no
values are set. Watch
buttons are pressed for 60 seconds, the watch will return to Date &
will return to Date &
Time mode.
Time mode when all
values are set.

CHRONO MODE

Illuminate
Start/Stop
Backlight
Chronograph
LAP
Stroke
Rate
Splits
Enter &
Exit Mode
To run the chronograph:
1. Press the Mode
button to enter
Chrono Mode.
2. Press the Start The chrono icon will blink when the timer is running. The lap time and
button to start the cumulative time will begin counting from 00:00.0. The lap counter will
chronograph.
show 00.
3. Press the Split The stored lap and cumulative time will freeze on the display for 8
button to store a lap. seconds, then resume. The lap counter will increase by 1, up to 99 laps.
4. Press the Stop
The chrono icon will stop blinking and the lap and cumulative times will
button to stop the freeze on the display. If the Start button is pressed again, the chronograph
chronograph. will resume timing without creating a lap.
Press the MODE button to
cycle through the modes:
TIME
CHRONO
RATE/TIME
RATE/CHRONO
ALARM
Indicates
Indicates
if alarm
is set AM or PM
Time of
Day
Day of
Date
the week
Indicates
Indicates
Chrono
Lap Number
Mode
LAP
Hour
Lap
indicator
Time
Cumulative
Time
To recall the data (the chronograph must be stopped):
1. Hold the Recall
"HOLD TO RECALL" will be displayed , with a beep when entering Recall
button for 3 seconds. Mode.
2. Press the + button The date and time when the chronograph was started will be displayed.
to cycle through the
After reviewing all splits, the Best Lap screen and Avgerage screen will
lap times. display the shortest and average of all stored laps.
3. Press the - button
to cycle through the
times in reverse
order.
4. Press the Mode
button to exit Recall.
5. Hold the Reset "HOLD TO CLEAR" and the chrono icon will be displayed. The watch will
button for 3 seconds beep once and clear the data and return the chronograph to 00:00.0.
to clear the data.
6. Press the Mode
If the Chrono mode is exited without clearing the data, the memory
button to exit will remain intact. If the Chrono mode is re-entered, the display will
Chrono Mode. show the chronograph stopped on the last stored time. If the Mode
button is pressed while the chronograph is running, the timer will
continute to run even though it will not be displayed.
** If the lap time on the chronograph reaches 59:59.59 (HH:MM:SS), a "01" will appear just below
the lap number, indicating the time is 1 hour. The Lap time will roll back to 00:00.00 and count up.
**The Manual Rate button will remain active in Chrono Mode, meaning rates can be measured at
any time while the chronograph is running. If the Manual Rate button is pressed twice within 10
seconds, the rate will be displayed instead of the lap. After 10 seconds of no Rate button presses,
the watch will return to regular Chrono mode. The Split and Start/Stop buttons will work the same.
The internal tilt switch will not measure a stroke rate in this mode.
RATE MODES (Rate/Time and Rate/Chrono)
The Cadence T1 measures stroke rates with an internal tilt switch that calculates the rate from
feathering and squaring the blade. The tilt switch can also be used on the wrist by tilting it in unison
with the feathering and squaring of an oar. It also measures rates when the Rate/Next button is
pressed in conjunction with a crew's catches. The watch updates the stroke rate once per stroke,
and can measure 6-240 strokes per minute.
Illuminate
Start/Stop
Backlight
Chronograph
LAP
Stroke
Rate
Splits
Enter &
Exit Mode
To measure stroke rates:
1. Press the Mode
button to enter either
Stroke Rate mode.
2. Measure the rate
When the stroke rate is triggered for the first time, the display will
with either Rate
show a 0 for the stroke rate. When triggered again within 10 seconds,
button or tilt switch.
the stroke rate will be calculated and displayed.
To use the chronograph while measuring rates:
1. Press the Mode
button to enter the
Rate/Chrono mode.
2. Press the Start
The chrono icon will blink when the timer is running. When the lap
button to start the button is pressed, the stored lap and cumulative time will freeze on
chronograph, and Split
the display for 8 seconds, then resume.
to store laps.
3. Press the Stop The Cadence will continue to measure the stroke rate with either the
button to stop the tilt switch or the rate button with the chronograph stopped. The
chronograph. chronograph may be restarted at any time.
To recall the stored laps:
1. With chronograph "HOLD TO RECALL" will be displayed, with a beep when entering Recall
Mode.
stopped, hold the
Recall button for 3
seconds.
2. ( The Recall will Both lap and cumulative times will be displayed, even though only the
function the same as in cumulative times were shown when the Rate/Chrono mode was
Chrono mode.)
timing.
3. Press the Mode
button to exit Recall.
4. Hold the Reset "HOLD TO CLEAR" will be displayed, with a beep when clearing the
button for 3 seconds chronograph. The display will return to Rate/Chrono mode.
to clear the data.
Rate/Chrono Mode
Rate/Time Mode
Chronograph
Indicates AM or PM
icon
Stroke
Stroke
Rate
Rate
Time
Cumulative
of Day
Chronograph Time
Indicates Lap
LAP