Parrot Uncle F6236BK Installation & Operating Instructions For The Owner's Installation, Manual

CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.IF UNSURE CONSULT
A QUALIFIED ELECTRICIAN
1. To avoid possible electric shock, turn off the electricity at the main fuse box or circuit panel before you begin
the fan installation or before servicing the fan or installing accessories.
2. Read all instructions and safety information carefully before installing your fan and save these instructions.
3. Make sure all electrical connections comply with local codes or ordinances and the National Electrical Code.
If you are unfamiliar with electric wiring, please use a qualified and licensed electrician.
4. Make sure you have a location selected for your fan that allow clear space for the blades to rotate, and at least
seven (7) feet of clearance between the floor and the fan blade tips. The fan should be mounted at least thirty
(30) inches from walls or other upright structures.
5. WARNING: The outlet box and ceiling support joist used must be securely mounted, and capable of
supporting at least 100 pounds. To reduce the risk of fire, electric shock or personal injury, mount to the outlet
box marked acceptable for fan supported and use mounting screws provided with the outlet box. The box must
be supported directly by the building structure.
6. WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked
"acceptable for fan support" and use mounting screws provided with the outlet box most outlet boxes commonly
used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult
a qualified electrician if in doubt.
7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must UL listed and
marked suitable for use with the model fan you are installing. Switches must be UL. general use switches. Refer
to the instructions packaged with the light kits and switches for proper assembly.
8. After installation is complete, check that all connections are absolutely secure.
9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up
into outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding
conductor on one side of the outlet box.
10. WARNING:
control device, or rheostat.
11. Do not separate the reverse switch until the fan has come to a complete stop.
12. Do not insert anything into the fan blades while they are rotating.
13. WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as
"flanges") during assembly or after installation. Do not insert objects in the path of the blades.
14. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning
the fan.
15. Do not use water or detergent when cleaning the fan or fan blades. A dry dust cloth or lightly dampened
cloth will be suitable for most cleaning.
NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all
possible conditions and situations that may occur. It must be understood that common sense and caution are
necessary factors in the installation and operation of this fan.
INSTALLING THE FAN
Tools Required: Phillips screwdriver, Pair of pliers, straight slot screwdriver, adjustable wrench, step ladder, and wire cutters.
INSTALLLING THE MOUNTING BRACKET
The ceiling fan must be installed in a location so that the blades are 12"( 300mm) spacing from the tip of the blade to the nearest objects or walls. When hanging the Fan REMEMBER to turn
off the power. Follow the instruction below to hang your fan properly:
1. For concrete ceiling, drill two holes in 2. For wood ceiling, install the
the ceiling and secure the mounting mounting bracket to the ceiling which
bracket to the ceiling with two is capable of carrying a load of at least
Φ0.32"(8mm) （ distance between the 100lbs(45kgs) with two long mounting
two holes should be appropriate） screws and washers provided. Be sure
expansion screws, flat washers,nuts at least 0.12"(30mm) of the screw is
provided and tighten with a spanner. threaded into the support.
NOTE:Hanger after the installation must be able to withstand the weight of 100lbs( 45kgs) or more
Installation & Operating Instructions for the
Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
THANK YOU FOR YOUR PURCHASE
instructions before using the product
NOTE: This product is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities are different or are impaired, or lack of experience or knowledge,
unless such persons are supervised or trained to operate the appliance by a person responsible for
their safety.
NOTE: Children should be supervised to ensure that they do not use appliances as a toy.
BEFORE INSTALLATION
SKU R t a d e o V a t l e g R t a d e p w o r e m ( t o ) r o
F6236BK 55W E26 2*40W(MAX.)EXCLUDE
F6236BN E26 2*40W(MAX.)EXCLUDE
55W
BEFORE INSTALLATION
Unpack your fan and check the contents.You should have the following:
1
2
18 19 20 21 22
3
4
5
6
8
7
9
12
10
13
11
14
15
16
17
1. Mounting bracket 9. Top housing
17. Light kit
2. Mounting screws 10. Lower housing
18. Wood screws
3. Canopy 11. Fan motor assembly
19. Expansion screws
12. Screws for Blades
4. Downrod & hanger ball
20. Screw washers
13. Blades
5. Canopy cover 21. Balancing tape
14. Blade bracket
6. Coupling cover 22. Balancing clip
7. Bolt 15. Screws for blade bracket
23. Remote control set.
8. Lock pin 16. Screws for Light kit
3. For installing to outlet box, secure the outlet box 4. Refer to the Fig. in right for mounting
directly to the building structure. Use appropriate when the ceiling is angled max. 15
fasterners and building materials. The outlet box and its degree angle.
support must be able to fully support the moving weight
of the fan(at least 100lbs). Use a UL listed metal outlet
box. Do not use a plastic outlet box. Figure 1& 2
examples to mount the outlet box.
F6236
Light CCT.
23
hr 2 4 8
3
2
1
Remove the tool Screws for Blades and Screws for blade bracket
1.
from the screw package.
2. blade bracket
Mount the cutter Blade bracketmounted to the Fan
Motor Assembly.
4. Install the Light kit to the junction box with by using the 3 screws
preinstalled on the Screws for Light kit.
Installation & Operating Instructions for the
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Coupling
Downrod &
hanger ball
Coupling
cover
Bolt
INSTALLING THE FAN TO MOUNTING BRACKET ON
CEILING
.
1.
2.
3.
USING YOUR CEILING FAN
F6236
Owner's Installation ,Manual
Canopy
Decorative
canopy cover
Lock pin
Set screw