Parrot Uncle F6236 Installation & Operating Instructions

CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.IF UNSURE CONSULT
A QUALIFIED ELECTRICIAN
1. To avoid possible electric shock, turn off the electricity at the main fuse box or circuit panel before you begin
the fan installation or before servicing the fan or installing accessories.
2. Read all instructions and safety information carefully before installing your fan and save these instructions.
3. Make sure all electrical connections comply with local codes or ordinances and the National Electrical Code.
If you are unfamiliar with electric wiring, please use a qualified and licensed electrician.
4. Make sure you have a location selected for your fan that allow clear space for the blades to rotate, and at least
seven (7) feet of clearance between the floor and the fan blade tips. The fan should be mounted at least thirty
(30) inches from walls or other upright structures.
5. WARNING: The outlet box and ceiling support joist used must be securely mounted, and capable of
supporting at least 100 pounds. To reduce the risk of fire, electric shock or personal injury, mount to the outlet
box marked acceptable for fan supported and use mounting screws provided with the outlet box. The box must
be supported directly by the building structure.
6. WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked
"acceptable for fan support" and use mounting screws provided with the outlet box most outlet boxes commonly
used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult
a qualified electrician if in doubt.
7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must UL listed and
marked suitable for use with the model fan you are installing. Switches must be UL. general use switches. Refer
to the instructions packaged with the light kits and switches for proper assembly.
8. After installation is complete, check that all connections are absolutely secure.
9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up
into outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding
conductor on one side of the outlet box.
10. WARNING:
control device, or rheostat.
11. Do not separate the reverse switch until the fan has come to a complete stop.
12. Do not insert anything into the fan blades while they are rotating.
13. WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as
"flanges") during assembly or after installation. Do not insert objects in the path of the blades.
14. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning
the fan.
15. Do not use water or detergent when cleaning the fan or fan blades. A dry dust cloth or lightly dampened
cloth will be suitable for most cleaning.
NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all
possible conditions and situations that may occur. It must be understood that common sense and caution are
necessary factors in the installation and operation of this fan.
INSTALLING THE FAN
Tools Required: Phillips screwdriver, Pair of pliers, straight slot screwdriver, adjustable wrench, step ladder, and wire cutters.
INSTALLLING THE MOUNTING BRACKET
The ceiling fan must be installed in a location so that the blades are 12"( 300mm) spacing from the tip of the blade to the nearest objects or walls. When hanging the Fan REMEMBER to turn
off the power. Follow the instruction below to hang your fan properly:
1. For concrete ceiling, drill two holes in 2. For wood ceiling, install the
the ceiling and secure the mounting mounting bracket to the ceiling which
bracket to the ceiling with two is capable of carrying a load of at least
Φ0.32"(8mm) （ distance between the 100lbs(45kgs) with two long mounting
two holes should be appropriate） screws and washers provided. Be sure
expansion screws, flat washers,nuts at least 0.12"(30mm) of the screw is
provided and tighten with a spanner. threaded into the support.
NOTE:Hanger after the installation must be able to withstand the weight of 100lbs( 45kgs) or more
Parrotuncle Lighting, 218 Black Tie Lane, Chapel Hill, NC www.parrotuncle.com
Parrot Uncle YOU CAN BE SURE OF are trademarks of Eileen Grays LLC.
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
THANK YOU FOR YOUR PURCHASE
instructions before using the product
NOTE: This product is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities are different or are impaired, or lack of experience or knowledge,
unless such persons are supervised or trained to operate the appliance by a person responsible for
their safety.
NOTE: Children should be supervised to ensure that they do not use appliances as a toy.
BEFORE INSTALLATION
SKU R t a d e o V a t l e g R t a d e p w o r e m ( t o ) r o
F6236BK 55W
F6236BN
55W
BEFORE INSTALLATION
Unpack your fan and check the contents.You should have the following:
1
2
18 19 20 21
3
4
5
6
8
7
9
12
10
13
11
14
15
16
17
1. Mounting bracket 9. Top housing
2. Mounting screws 10. Lower housing
3. Canopy 11. Fan motor assembly
12. Screws for Blades
4. Downrod & hanger ball
13. Blades
5. Canopy cover
14. Blade bracket
6. Coupling cover
7. Bolt 15. Screws for blade bracket
8. Lock pin 16. Screws for Light kit
3. For installing to outlet box, secure the outlet box 4. Refer to the Fig. in right for mounting
directly to the building structure. Use appropriate when the ceiling is angled max. 15
fasterners and building materials. The outlet box and its degree angle.
support must be able to fully support the moving weight
of the fan(at least 100lbs). Use a UL listed metal outlet
box. Do not use a plastic outlet box. Figure 1& 2
examples to mount the outlet box.
Used under license by Eileen Grays LLC.
All rights reserved.
F6236
Light CCT.
E26 2*40W(MAX.)EXCLUDE
E26 2*40W(MAX.)EXCLUDE
23
22
2 4 8 hr
3
2
1
Remove the tool Screws for Blades and Screws for blade bracket
1.
from the screw package.
2.
Mount the cutter Blade bracketmounted to the Fan
Motor Assembly.
17. Light kit
18. Wood screws
19. Expansion screws
20. Screw washers
4. Install the Light kit to the junction box with by using the 3 screws
21. Balancing tape
22. Balancing clip
preinstalled on the Screws for Light kit.
23. Remote control set.
Parrotuncle Lighting, 218 Black Tie Lane, Chapel Hill, NC
Made in China Parrot Uncle YOU CAN BE SURE OF are trademarks of Eileen Grays LLC.
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
Coupling
Downrod &
hanger ball
INSTALLING THE FAN TO MOUNTING BRACKET ON
CEILING
blade bracket
1.
2.
3.
USING YOUR CEILING FAN
www.parrotuncle.com
Used under license by Eileen Grays LLC.
F6236
Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
Canopy
Decorative
canopy cover
Coupling
cover
Lock pin
Bolt
Set screw
.
All rights reserved. Made in China