Advertisement
Quick Links
SS-TH60 – 1/2" MINIATURE THERMOSTATIC VALVE WITH VOLUME CONTROL
SS-TH70 – 1/2" MINIATURE THERMOSTATIC VALVE WITH 2-WAY DIVERTER
SS-TH80 – 1/2" MINIATURE THERMOSTATIC VALVE WITH 3-WAY DIVERTER
Features:
•
Ability to pre-select water temperature – thus conserving water
•
Compensates for water pressure fluctuations preventing scalding
•
Safety button at 100°F prevents accidental scalding
•
High flow rates allow for multiple shower applications
Specifications:
o Operating pressure is 20 PSI to 85 PSI
o When pressure is higher than 85 PSI a pressure reducer (fitted before the valve) is required.
o Temperature range is 60°F to 115°F
o Recommended supply setting is 45 PSI and 150°F
Note:
•
DO NOT USE PLUMBER'S PUTTY ON ANY OF THE BRASS COMPONENTS
This will cause the finish to tarnish and void the warranty. A non-corrosive Alkoxy Silicone is
recommended.
•
DURING SWEATING OF LINES DO NOT OVERHEAT CASTING
Overheating may cause damage to internal mechanism and void the manufacturer's warranty as
well as increase the risk of scalding.
•
COPPER ADAPTORS MAY BE REQUIRED TO COMPLETE YOUR INSTALLATION
•
Shipping weight (lbs.): 4
•
Shipping dimension (in.): 8 x 11 x 5
SS-TH60
Valve Installation
1. Flush the lines of all dirt and debris. Failure to completely flush the lines will cause valve failure and
will void the manufacturer's warranty.
2. Fit the valve on the wall without removing the plastic cover on the control spindle. Turning the
control spindle will change the temperature setting which is pre-calibrated at the factory.
3. Connect the hot water supply to the left inlet of the valve (hot marked with "H") and cold supply to
the right inlet (cold marked with "C").
MINIATURE THERMOSTATIC VALVE
Diagram 1: Flow Rate Vs. Pressure
INSTALLTION FOR
SS-TH70/80
Rev. 8/19
P a g e
| 1
Advertisement
Related Manuals for Watermark SS-TH60
Summary of Contents for Watermark SS-TH60
- Page 1 INSTALLTION FOR MINIATURE THERMOSTATIC VALVE SS-TH60 – 1/2” MINIATURE THERMOSTATIC VALVE WITH VOLUME CONTROL SS-TH70 – 1/2" MINIATURE THERMOSTATIC VALVE WITH 2-WAY DIVERTER SS-TH80 – 1/2" MINIATURE THERMOSTATIC VALVE WITH 3-WAY DIVERTER Features: • Ability to pre-select water temperature – thus conserving water •...
- Page 2 INSTALLTION FOR MINIATURE THERMOSTATIC VALVE 4. Use the Plastic Mudguard (1) (part of the package) to position the Valve (2) in the wall. This is done by checking the markings on the mudguard for the minimum/maximum settings which is 2 3/8” to 2 7/8”...
-
Page 3: Temperature Setting
INSTALLTION FOR MINIATURE THERMOSTATIC VALVE Diagram 4: Representative Trim Parts Checklist Carefully remove all parts from the box. The following parts should be included. Item # Description Qty. Item # Description Qty. Temperature Control Dome Temperature Control Screw Dome Sleeve (raw brass) Temperature Control Handle Face Plate Volume Control Dome... - Page 4 INSTALLTION FOR MINIATURE THERMOSTATIC VALVE Removal and Maintenance of Cartridge (see Diagram 6) This thermostatic cartridge has screens to prevent dirt and unwanted particles from damaging the valve. Clogged screens can cause reduced flow and inefficient temperature mixture by the valve. You can easily clean the screens by following the instructions below.
- Page 5 INSTALLTION FOR MINIATURE THERMOSTATIC VALVE Troubleshooting Malfunction Cause Remedy Cannot regulate temperature Dirt in check valves Remove and clean check valves Water supply reversed Reverse hot and cold supply lines Valve installed upside down Reverse valve Hot and cold water do not mix Lack of water pressure at one Correct water pressure at source of the inlets Blocked shower head...
- Page 6 INSTALLTION FOR MINIATURE THERMOSTATIC VALVE Diagram 7: Dimensional Drawings SS-TH60: SS-TH70: SS-TH80: Miniature Thermostatic Valve P a g e...